User manual PIONEER HTZ252DVD (XV-DV252)

[. . . ] Also, the use of this remote control may cause other devices to work improperly. · When the operating range of the remote becomes too short, replace the batteries. Additional notes on speaker placement If your listening room is of adequate size, place the speakers as shown in step 3 to achieve the optimum surround sound effect. If you are listening in a fairly small room and a typical surround speaker setup is not possible, see Home theater sound setup in the instruction manual and the Speaker Setup Guide for information on the Front Surround 3-spot setup option. When using the standard surround speaker setup as shown in step 3, please observe the following guidelines: · Install the main front left and right speakers at an equal distance from the TV. [. . . ] · For optimum effect, install the rear speakers slightly above ear level. · Install the center speaker above or below the TV so that the sound of the center channel is localized at the TV screen. CLEAR SHIFT SLEEP SURROUND DISPLAY FRONT SURROUND 4 Fix the AM loop antenna to the attached stand. To fix the stand to the antenna, bend in the direction indicated by the arrow (fig. A) then clip the loop onto the stand (fig. Note: If you plan to mount the AM antenna to a wall or other surface, secure the stand with screws (fig. C) before clipping the loop to the stand. Make sure the reception is clear. ANTENNA 2 3 AM LOOP ANTENNA Remote control battery caution Incorrect use of batteries may cause leakage or rupture. Always be sure to follow these guidelines: · Always insert batteries into the battery compartment correctly matching the positive ª and negative · polarities, as shown by the display inside the compartment. · Never mix new and used batteries. · Batteries of the same size may have different voltages, depending on brand. Match them to the colored speaker terminals on the rear panel of the DVD/CD receiver. Surround right (Grey) Surround left (Blue) Connect each speaker as shown below. (Subwoofer connentions start from step 3) Color-coded wire (Connect to speaker) Color-coded connector (Connect to rear panel) 4 Connect the DVD/CD receiver to your TV, then connect the supplied power cord. 1 Connect one end to a video input on your TV. Use the supplied video cord. 1 2 COMPONENT VIDEO OUT VIDEO OUT VIDEO OUT VIDEO CB/ PB CR/ PR Twist and pull off the protective shields on each wire. Match the colored wire with the color-coded label (above the tabs), then insert the colored wire into the red (+) tab and the other wire with the black (­) tab. color-coded speaker terminals on the rear of the DVD/CD receiver (as shown at left). The small lug at the wire-end of the speaker plug should face up or down depending on whether it's being plugged into one of the upper or lower three speaker terminals. Please make sure to connect correctly. 2 Connect the other end to the video output of the DVD/CD receiver. This player is equipped with copy protection technology. Do not connect this player to your TV via a VCR using AV cables, as the picture from this player will not appear properly on your TV. IN L LINE OUT L FRONT R L CENTER Listening position Subwoofer (Purple) SURROUND R 3 Connect the power cord to the AC inlet. Y R AUDIO R L SPEAKERS SUB WOOFER VIDEO IN 3 Connect the other end to the COMPONENT VIDEO OUT VIDEO OUT S-VIDEO OUT VIDEO ANTENNA COMPONENT VIDEO OUT AM LOOP ANTENNA CB/ PB CR/ PR CB/ PB CR/ PR For the best surround sound, setup your speakers as above. The front left and right speakers should be about 1. 8­2. 7 m apart. Center (Green) A Y Upper three terminals IN L LINE OUT L FRONT R L CENTER FM UNBAL 75 VIDEO OUT S-VIDEO OUT VIDEO Y R AUDIO R SURROUND R L SPEAKERS SUB WOOFER AC IN These speaker terminals can be hazardous when live. When you connect or disconnect the speaker cables, to prevent the risk of electric shock, do not touch uninsulated parts before disconnecting the power cord. Front right (Red) Front left (White) Lower three terminals AC IN Congratulations!Printed in To AC outlet <ARE7358-A> Speaker Setup Guide What's in the box · Front speakers x 2 · Center speaker x 1 · Surround speakers x 2 · Subwoofer x 1 · Speaker cords: Red/White (Front speakers) 4m x 2 Green (Center speaker) 4m x 1 Blue/Grey (Surround speakers) 10m x 2 · Non-skid pads (small) x 4 · Non-skid pads (large) x 4 · Front speaker stand bases x 2 · Screws (for bases) x 6 · Brackets x 2 · Screws (for brackets) x 4 · Mounting brackets x 2* · Screws (for mounting brackets) x 2* *Please refer to Wall-mounting the front and surround speaker system in the operating instructions for installation. Assembling the speaker stands and securing your front speakers Attach the speaker stand bases to the stems using the screws provided. Before securing the base to the stand, thread the speaker wire through the holes provided on the base as shown below. [. . . ] When you connect or disconnect the speaker cables, to prevent the risk of electric shock, do not touch uninsulated parts before disconnecting the power cord. Front right (Red) Front left (White) Lower three terminals AC IN Congratulations!Printed in To AC outlet <ARE7358-A> Speaker Setup Guide What's in the box · Front speakers x 2 · Center speaker x 1 · Surround speakers x 2 · Subwoofer x 1 · Speaker cords: Red/White (Front speakers) 4m x 2 Green (Center speaker) 4m x 1 Blue/Grey (Surround speakers) 10m x 2 · Non-skid pads (small) x 4 · Non-skid pads (large) x 4 · Front speaker stand bases x 2 · Screws (for bases) x 6 · Brackets x 2 · Screws (for brackets) x 4 · Mounting brackets x 2* · Screws (for mounting brackets) x 2* *Please refer to Wall-mounting the front and surround speaker system in the operating instructions for installation. Assembling the speaker stands and securing your front speakers Attach the speaker stand bases to the stems using the screws provided. Before securing the base to the stand, thread the speaker wire through the holes provided on the base as shown below. Then, once you have aligned the stem and base, secure with the small screws at the points shown at right. Safety precautions when setting up When assembling the speakers, lay them down flat on their side to avoid accidents or injury. Make sure to use a stable surface when assembling, setting up, and placing the speakers. Standard surround 5-spot setup This is a standard multichannel surround sound speaker setup for optimal 5. 1 channel home theatre sound. 1 Attach the smaller non-skid pads to the base of the center speaker. [. . . ]