User manual PIONEER KEH-P8200RDS
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual PIONEER KEH-P8200RDS. We hope that this PIONEER KEH-P8200RDS user guide will be useful to you.
Lastmanuals help download the user guide PIONEER KEH-P8200RDS.
Manual abstract: user guide PIONEER KEH-P8200RDS
Detailed instructions for use are in the User's Guide.
[. . . ] By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.
!!
!
!
In case of trouble
Should this product fail to operate properly, please contact your dealer or nearest authorized Pioneer Service Station.
!
!
Before connecting/ installing the amplifier
WARNING
!The use of a special red battery and ground wire RD-228, available separately, is recommended. Connect the battery wire directly to !
the car battery positive terminal + and the ground wire to the car body. [. . . ] In such a case, please contact the nearest authorized Pioneer Service Station. Level adjustment control of this unit
!If the amplifier level adjustment control is raised inappropriately, this will simply increase distortion, with little increase in power. If the signal waveform is distorted by high output, raising the level adjustment control of the amplifier only changes the power slightly.
6
En
Section
Connecting the units
03
Setting example
In this system, connect this unit to 4 channels in 1, and 3 channels in 2.
3 1 7 4 5 2 7 6
Connection diagram
d c 1 2 3 4 5
Connecting the units
8 d e f
9
a
b e 7
6
c
In this system, connect 2 channels to each unit.
3 7 4 7 5 7 6 7 a b 9
8
f
8 d e f
3 4 5 6 7 8 9 a b c d e f
9 c
a
b
Tweeter Middle-range speaker Low-range speaker Subwoofer This unit High range output Mid range output Low range output Subwoofer output RS-P99 (sold separately) Optical cable IP-BUS cable Analog signal
1 Special red battery wire RD-228 (sold separately) After completing all other amplifier connections, finally connect the battery wire terminal of the amplifier to the positive (+) battery terminal. 2 Ground wire (Black) RD-228 (sold separately) Connect to a clean, paint-free metal location. 3 Car stereo with RCA output jacks (sold separately) 4 RS-P99 (sold separately) 5 External output If only one input plug is used, do not connect anything to RCA input jack B. 6 Connecting wire with RCA pin plugs (sold separately) 7 RCA input jack A 8 RCA input jack B
En
7
Section
03
Connecting the units
9 Speaker output terminals Please see the following section for speaker connection instructions. Refer to Connecting the speaker output terminals on page 12. a Fuse (25 A) b System remote control wire (sold separately) Connect male terminal of this wire to the system remote control terminal of the car stereo. The female terminal can be connected to the auto-antenna relay control terminal. If the car stereo lacks a system remote control terminal, connect the male terminal to the power terminal via the ignition switch. (RCA output) If only one input plug is used, connect the plug to RCA input jack A rather than B.
Two-channel output (Mono)
1
1
1 Speaker (Mono)
Two-channel output (Stereo) / (Mono) !Slide INPUT SELECT (input select) switch to 2CH position. Set the LEFT CHANNEL (left channel) and RIGHT CHANNEL (right channel) switches to the same position.
1
Connections when using the RCA input jack
Connect the car stereo RCA output jack and the RCA input jack of the amplifier. Slide INPUT SELECT (input select) switch to 4CH position.
3
1 RCA input jack A For two-channel output, connect the RCA plugs to the RCA input jack A.
2
10
En
Section
Connecting the units
03
2 Connecting wires with RCA plugs (sold separately) 3 From RS-P99 (sold separately) etc. (RCA output)
Connecting the power terminal
Connecting the units
WARNING
!The use of a special red battery and ground wire RD-228, available separately, is recommended. Connect the battery wire directly to the car battery positive terminal (+) and the ground wire to the car body. If the battery wire is not securely fixed to the terminal using the terminal screws, there is a risk of overheating, malfunction and injury, including minor burns.
Solderless terminal connections
!Do not connect cords with exposed core wires to the amplifier power terminals (power terminal, ground terminal, system remote control terminal), since disconnection or breakage may result in fire or shortcircuit. Periodically inspect and tighten the wire as necessary. Do not solder or bind the ends of the twisted wires. [. . . ] Negative type Current consumption . . . . . . . . . . . . 27 A (at continuous power, 4 W) 3 A (No signal) Average current drawn . . . . . . . . . 9 A (4 W for four channels) 9 A (4 W for two channels) Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 A × 2 Dimensions (W × H × D) . . . [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE PIONEER KEH-P8200RDS
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual PIONEER KEH-P8200RDS will begin.
