User manual PIONEER PDK-TS05

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual PIONEER PDK-TS05. We hope that this PIONEER PDK-TS05 user guide will be useful to you.

Lastmanuals help download the user guide PIONEER PDK-TS05.


Mode d'emploi PIONEER PDK-TS05
Download
Manual abstract: user guide PIONEER PDK-TS05

Detailed instructions for use are in the User's Guide.

[. . . ] Do not install it outdoors, at a hot spring, or near a beach. Do not install the stand where it may be subjected to vibration or shock. There have been cases where unforeseen accidents such as the equipment breaking or falling over occurred after the installation of the display because the stand was not installed as instructed. The display must always be installed by two or more people to assure it is installed safely. [. . . ] note Be sure to install it on a flat stable location. Insert the screws in the holes vertically and do not tighten them with more force than necessary. Make sure that you install the support columns reliably according to the settings of the type of speakers you have purchased with reference to the procedure in Assembling the Stand. Illustration: when using support columns L Fit the stand's support columns to the bottom of the plasma display as indicated by the arrows, then slowly insert them vertically. Be extremely careful not to insert the support columns of the stand into any part of the plasma display other than the stand insertion slots. Note that doing so might damage the plasma display panel or its ports or result in the warping of the stand. Line up the column supports with the bottom of the plasma display as indicated in the accompanying diagram. Only when attaching speakers at the bottom of the plasma display Illustration: when using support columns S Note Please do not use the spacer if the speakers are to be attached to both sides of the plasma display. On this stand, you can adjust the angle of inclination of the plasma display within a range of 2° forward or backward according to your preference. Firmly tighten the forward/backward inclination anchor bolts on the left and right sides by rotating them downward using the enclosed C wrench. Be sure to hold the top of the plasma display with your hand until you have fully tightened the bolts. Be sure to adjust the angle only after you have attached the plasma display. Be sure to install it on a flat table or other flat surface. Be sure to hold the top of the plasma display with your hand while adjusting the angle. While being sure to hold the top of the plasma display with your hand, loosen the forward/backward inclination anchor bolts on the left and right sides by rotating them upwards using the enclosed C wrench. Check once more to make sure that the forward/backward inclination anchor bolts are fully tightened. Set the angle you prefer by slowly moving the plasma display. Be sure to observe the following precautions when moving or installing this product with a plasma display into a rack or other enclosure. Make sure that you always secure a space at least as large as that shown in the following diagram in front of and behind the table top stand. When moving the product more than a few meters, first remove the speaker, then remove the plasma display from the stand and move the speaker, plasma display, and stand separately. When detaching the plasma display from the stand, be sure to follow the procedure described in "Detaching the Plasma Display from the Stand" on page 22. Precautions when installing in a rack or other enclosure When installing in a rack or other enclosure, hold the plasma display by the handles located on the rear Caution and bottom of the plasma display. [. . . ] Holding the plasma display by its handles and from the bottom, lift the display vertically. Place the plasma display slowly onto the sheet laid out in step 2 with its screen facing downwards. Note When reattaching the plasma display to the stand, be certain that the left/right support columns are set at the same angle. The above specifications and exterior may be modified without prior notice to improve the product. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE PIONEER PDK-TS05

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual PIONEER PDK-TS05 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag