User manual PIONEER PDP-61MXE1

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual PIONEER PDP-61MXE1. We hope that this PIONEER PDP-61MXE1 user guide will be useful to you.

Lastmanuals help download the user guide PIONEER PDP-61MXE1.


Mode d'emploi PIONEER PDP-61MXE1
Download
Manual abstract: user guide PIONEER PDP-61MXE1

Detailed instructions for use are in the User's Guide.

[. . . ] This product is marketed assuming that it is installed by qualified personnel with enough skill and competence. Always have an installation specialist or your dealer install and set up the product. PIONEER cannot assume liabilities for damage caused by mistake in installation or mounting, misuse, modification or a natural disaster. After installation, be sure to deliver this manual to the customer and explain to the customer how to handle the product. [. . . ] Speed clamps are designed to be difficult to undo once in place. To attach the speed clamps to the main unit Connect the speed clamps using the 4 holes marked with · Using pliers, twist the clamp 90° and pull it outward. In some cases the clamp may have deteriorated over time and may get damaged when removed. Follow the procedure described below and make settings as they apply to the type of components connected. These settings are required only when using the following input signal refresh rates: 1 31. No manual setup is necessary for signals with other refresh rates, since adjustments are performed automatically (the SETTING item will not be displayed). Press STANDBY/ON to put the unit in the operation mode. Make this setup for each input (INPUT1 and INPUT2). Depending on the signal, analog RGB signals may result in the screen image appearing with a whitish or greenish cast. Make this CLAMP POSITION setting for each applicable input (INPUT1 and INPUT2). When using this setup, be sure to carefully check the signal output of the component that you are using. Although these modes are designed for full display of a picture on a wide screen, it is our hope that you make use of them with a full understanding of the manufacturer's intentions. The size of the image displayed on the screen, and the range of the image shown can be set in one of four modes on the PDP-61MXE1, and in three modes on the PDP-433MXE. 480 lines 768 lines The screen size changes each time SCREEN SIZE is pressed as follows. ) [PDP-433MXE] * The PDP-433MXE is designed with horizontally oblong elements, with the result that the image displayed will appear more oblong than the original input signal. When the PARTIAL or FULL setting is used to display a nonwide screen 4:3 picture fully on a wide screen, a portion of the picture may be cut off or appear deformed. Be aware that when the display is used for commercial or public viewing purposes, selecting the PARTIAL or FULL mode settings may violate the rights of authors protected under copyright law. When DOT BY DOT or 4:3 screen sizes are selected, the display position is moved slightly each time the power is turned on, in order to prevent image burning. ) 2 4:3 The display fills the screen as much as possible without altering the aspect ratio of the input signal. 3 FULL The display is presented with a widescreen aspect ratio of 16:9 and fills the entire screen. 480 lines 768 lines 4 PARTIAL (*Supported only on PDP-61MXE1) The PARTIAL setting is available only during personal computer input (1280 x 1024/60 Hz only). However, in order to maintain the 1:1 ratio, a portion of the display will not appear on the screen. [. . . ] 4 If the display is moved suddenly from a chilled location to a warm room, or if the room temperature rises suddenly, condensation may form on internal parts. To protect internal circuitry, the display is provided with a condensation detector that automatically disables power in event of internal condensation; in this case, allow the unit to dry thoroughly before using. If the power is automatically turned off for a reason other than the above reasons, there could be a malfunction. In this case, unplug the power cord from the power outlet and request repair from your nearest sales outlet. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE PIONEER PDP-61MXE1

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual PIONEER PDP-61MXE1 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag