User manual PIONEER PRO-1140HD

[. . . ] PLASMA DISPLAY SYSTEM PRO-1140HD PRO-940HD Register Your Product on www. pioneerelectronics. com (US) www. pioneerelectronics. ca (Canada) Operating Instructions 1) 2) 3) 4) 5) 6) 7) Read these instructions. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. [. . . ] Use Manual Setup to optimize the positions and clock of images when necessary. Selecting a screen size manually In single-screen mode, press SCREEN SIZE to change the size of the screen. The Video signal determines the available screen size options. · The selectable screen sizes differ depending on the type of input signal. ( / then ENTER) then ENTER) then ENTER) AV mode Item 4:3 FULL ZOOM 0 0 Select "Manual Setup". ( / Description For 4:3 "standard" pictures (side bar appears on each side) For 16:9 squeezed pictures For 16:9 letterbox pictures (bars may appear on the top and bottom on some programs) For 14:9 letterbox pictures (bars may appear on the top and bottom on some programs) In this mode pictures are stretched to fill the screen, side to side Select an item to be adjusted. ( / Manual Setup H/V Position Adjust Clock Phase Reset CINEMA WIDE 5 Perform adjustment. ( / or / ) · With "Clock" or "Phase" selected, you can change the parameter using / . NOTE · Avoid displaying signals that do not completely fill the screen. This may cause temporary or permanent image retention depending on the frequency and duration. 6 Press HOME MENU again to exit the menu. NOTE · To restore all factory defaults, press / to select "Reset" in step 4 then press ENTER. Press / to select "Yes" then press ENTER. PC mode except for XGA signals Item 4:3 FULL Dot by Dot Description Fills the screen without altering the input signal aspect ratio Full 16:9 screen display Matches input signal to the same number of screen pixels PC mode for XGA signals (Ex. 1024 × 768 input with PRO-1140HD) Item 4:3 Description Matches input signal to the same number of screen pixels Optimized for 1024 × 768 display Full 16:9 screen display Optimized for 1024 × 768 display For wide signal display Use when displaying 1360 × 768 signal resolution FULL1 FULL2 NOTE · In 2-screen mode, press SCREEN SIZE to change the size of the left screen. · For the PRO-940HD the number of panel pixels is different. Signal processing and actual viewing conditions vary slightly. 63 En 11 Adjustments and Settings · When watching a High Definition TV broadcast, press SCREEN SIZE to cycle through FULL, ZOOM, WIDE, and 4:3. · High Definition TV broadcasting with WIDE selected may hide some of the screen image. · Some HD broadcasts may display 4:3 content with side masks. Extended viewing with the sides masked can cause uneven wear. After viewing 4:3 content, try watching a program in full screen motion video. Selecting a screen size automatically The Plasma Display automatically selects an appropriate screen size when video signals are received from a connected HDMI device (see page 67). To activate this function, use the following procedure. AV mode 1 2 3 4 Press HOME MENU. ( / Auto Size Off On then ENTER) then ENTER) Select "Auto Size". ( / then ENTER) 4:3 Item Description Deactivates the Auto Size function Activates the Auto Size function WIDE FULL Off (factory default) On 5 Press HOME MENU again to exit the menu. CINEMA ZOOM NOTE · Manually select an appropriate screen size if an image does not automatically switch to the correct screen format. · When the video signal contains no aspect ratio information, automatic screen sizing is unavailable. PC mode except for XGA signals 4:3 Selecting a screen size for 4:3 aspect ratio signals With the Auto Size function activated, choose whether the Plasma Display should choose the 4:3 mode or WIDE mode when 4:3 aspect ratio signals are received. Dot by Dot PC mode for XGA signals FULL 1 2 3 4 Press HOME MENU. ( / then ENTER) then ENTER) then ENTER) Select "WIDE" or "4:3". ( / 4:3 Mode WIDE 4:3 4:3 FULL2 FULL1 Item WIDE (factory default) Description Wide image without side masks 4:3 aspect ratio with side masks NOTE · The selectable screen sizes may differ depending on the conditions. 4:3 WIDE 4:3 5 Press HOME MENU again to exit the menu. 64 En Adjustments and Settings 11 Changing the brightness on both sides of the screen (Side Mask) With the 4:3 screen size selected for the AV mode, you can change the brightness of the gray vertical bars (side masks) that appear on the sides of the screen. Language setting To change the language being used for on-screen displays (such as menus in French or Spanish instead of English), follow the instructions below. [. . . ] and/or its related affiliates are not in any way liable for the accuracy or availability of the program schedule information or other data in the TV Guide On Screen system and cannot guarantee service availability in your area. In no event shall Gemstar-TV Guide International, Inc. and/or its related affiliates be liable for any damages in connection with the accuracy or availability of the program schedule information or other data in the TV Guide On Screen system. Copyright protection · This product incorporates copyright protection technology that is protected by U. S. patents and other intellectual property rights. [. . . ]