User manual PIONEER S-J220
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual PIONEER S-J220. We hope that this PIONEER S-J220 user guide will be useful to you.
Lastmanuals help download the user guide PIONEER S-J220.
Manual abstract: user guide PIONEER S-J220
Detailed instructions for use are in the User's Guide.
[. . . ] The S-J220 series has a built-in level converter, allowing direct connection from the rear-panel CAT jack to the serial port of your computer without the need of any external boxes. You will need a serial cable for connection to the RS-232C (serial or COM port) connector on your computer. [. . . ] If your computer uses a custom connector, you may have to construct the cable. In this case, refer to the technical documentation supplied with your computer for correct data connection. Vertex Standard does not produce CAT System operating software due to the wide variety of personal computers and operating systems in use today. However, the information provided in this chapter explains the serial data structure and opcodes used by the CAT system. This information, along with the short programming examples, is intended to help you start writing programs on your own. As you become more familiar with CAT operation, you can customize programs later on for your operating needs and discover the true operating potential of this system.
CAT JACK
PIN NO.
PIN NAME N/A SERIAL OUT SERIAL IN N/A GND N/A RTS
I/O --Output Input ------Input
CTS
Output
N/A
---
FUNCTION --Outputs the Serial Data from the transceiver to the computer. For example, when correct parameter is "IS0+1000" (IF SHIFT): IS01000; Not enough parameters specified (No direction (+) given for the IF shift) IS0+100; Not enough digits (Only three frequency digits given) IS0_+_1000; Unnecessary characters between parameters IS0+10000; Too many digits (Five frequency digits given) Note: If a particular parameter is not applicable to the S-J220, the parameter digits should be filled using any character except the ASCII control codes (00 to 1Fh) and the terminator (;).
There is three for the S-J220 Command as shown below: Set command: Set a particular condition (to the S-J220) Read command: Reads an answer (from the S-J220) Answer command: Transmits a condition (from the S-J220) For example, note the following in the case of the FA command (Set the main band (VFO-A) frequency): To set the main band (VFO-A) frequency to 14. 250000 MHz, the following command is sent from the computer to the transceiver: "FA14250000;" (Set command) To read the main band (VFO-A) frequency, the following command is sent from the computer to the transceiver: "FA;" (Read command) When the Read command above has been sent, the following command is returned to the computer: "FA14250000;" (Answer command)
Terminator
To signal the end of a command, it is necessary to use a semicolon (;). The digit where this special character must appear differs depending on the command used.
Alphabetical Commands
A command consists of 2 alphabetical characters. You may use either lower or upper case characters. The commands available for this transceiver are listed in the "PC Control Command Tables" on the following pages.
S-J220 SERIES CAT OPERATION REFERENCE
Page 2
CAT (COMPUTER AIDED TRANSCEIVER) OPERATION
CONTROL COMMAND LIST
COMMAND AB AC AG AI AM AN BA BC BD BI BP BS BU BY CA CH CN CO CS CT DA DN DP DS ED EU EX FA FB FR FS FT GT ID IF IS KM KP KR KS KY LK LM MA MC MD MG MK ML FUNCTION VFO-A TO VFO-B ANTENNA TUNER CONTROL AF GAIN AUTO INFORMATION VFO-A TO MEMORY CHANNEL ANTENNA NUMBER VFO-B TO VFO-A AUTO NOTCH BAND DOWN BREAK-IN MANUAL NOTCH BAND SELECT BAND UP BUSY CLASS-A CHANNEL UP/DOWN CTCSS NUMBER CONTOUR CW SPOT CTCSS DIMMER DOWN DISPLAY DIMMER SWITCH ENCORDER DOWN ENCORDER UP MENU FREQUENCY VFO-A FREQUENCY VFO-B FUNCTION RX FAST STEP FUNCTION TX AGC FUNCTION IDENTIFICATION INFORMATION IF-SHIFT KEYER MEMORY KEY PITCH KEYER KEY SPEED CW KEYING LOCK LOAD MESSAGE MEMORY CHANNEL TO VFO-A MEMORY CHANNEL MODE MIC GAIN MODE KEY MONITOR LEVEL SET READ ANS. O O O O O O O O O O O O O X O O O O O O O O O O O O O O O O O O O X X O O O O O O O O O O O O O O X O O O X O X O X O O X X O O X O O O O O X O O X X O O O O O O O O O O O O O O X O O X O O O X O X O O O X O X O X O O X X O O X O O O O O X O O X X O O O O O O O O O O O O O O X O O X O O O X O AI X O O X X O X O X O O X X O O X O O O O X X O O X X O O O O O O O X O O X O O O X O X X X O O X O COMMAND MR MS M W MX NA NB NL NR OI OS PA PB PC PL PR PS QI QR QS RA RC RD RF RG RI RL RM RO RS RT RU SC SD SF SH SM SQ SV TS TX UL UP VD VF VG VM VS VX XT FUNCTION MEMORY READ METER SW MEMORY WRITE MOX SET NARROW NOISE BLANKER NOISE BLANKER LEVEL NOISE REDUCTION OPPOSITE BAND INFORMATION OFFSET (REPEATER SHIFT) PRE-AMP (IPO) PLAY BACK POWER CONTROL SPEECH PROCESSOR LEVEL SPEECH PROCESSOR POWER SWITH QMB STORE QMB RECALL QUICK SPLIT RF ATTENUATOR CLAR CLEAR CLAR DOWN ROOFING FILTER RF GAIN RADIO INFORMATION NOISE REDUCTION LEVEL READ METER ROTATOR RADIO STATUS CLAR CLAR UP SCAN SEMI BREAK-IN DELAY TIME SUB-DIAL FUNCTION WIDTH S METER SQUELCH LEVEL SWAP VFO TXW TX SET UNLOCK UP VOX DELAY TIME VRF FILTER VOX GAIN [V/M] KEY FUNCTION VFO SELECT VOX TX CLAR SET READ ANS. X O O O O O O O X O O O O O O O O O O O O O O O X O X O X O O O O O O X O O O O X O O O O O O O O O O X O O O O O O O O O O O O O X X X O X X O O O O O O O O X O O O O O O X O O O X O O O X O O O O O X O O O O O O O O O O O O O X X X O X X O O O O O O O O X O O O O O O X O O O X O O O X O O O AI X O X O O O O O X O O X O O O X X X X O X X O O O O O X O O X O O O O O O X O O O X O O O X O O O
Page 3
S-J220 SERIES CAT OPERATION REFERENCE
CAT (COMPUTER AIDED TRANSCEIVER) OPERATION
CONTROL COMMAND TABLES
AB Set Read Answer AC Set Read Answer AG Set Read Answer AI Set Read Answer AM Set Read Answer AN Set Read Answer BA Set Read Answer BC Set Read Answer BD Set Read Answer VFO-A TO VFO-B
1 2 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
A
1 1
B
2 2
;
3 3
ANTENNA TUNER CONTROL
1 2 3 3 4 4 4 5 5 5 6 7 7 7 8 8 8 9 9 9 10 10 10
A
1
C
2
P1 P2 P3 ;
3
;
6 6
P1 0: Fixed P2 0: Fixed
P3 0: Tuner "OFF" 1: Tuner "ON" 2: Tuning Start
A
1
C
2
A
C
P1 P2 P3
;
P1 0: Main (VFO-A) Band Receiver 1: Sub (VFO-B) Band Receiver P2 000 - 255
AF GAIN
1 2 3 3 4 4 5 5 5 6 6 6 7 8 8 8 9 9 9 10 10 10
A
1
G
2
P1 P2 P2 P2 P1
3
;
7 7
A
1
G
2
;
4
A
1
G
2
P1 P2 P2 P2
3 4 5 5 5 6 6 6
;
7 7 7 8 8 8 9 9 9 10 10 10
AUTO INFORMATION A
1
I
2
P1
3
;
4 4
P1 0: Auto Information "OFF" 1: Auto Information "ON" This parameter is set to "0" (OFF) automatically when the transceiver is turned "OFF. "
A
1
I
2
;
3
A
I
P1
;
VFO-A TO MEMORY CHANNEL
1 2 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
A
1 1
M
2 2
;
3 3
ANTENNA NUMBER
1 2 3 3 4 4 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
A
1
N
2
P1 P2 P1
3
;
5 5
P1 0: Main (VFO-A) Band 1: Sub (VFO-B) Band
A
1
N
2
;
4
P2 1: 2: 3: 4: 5:
ANT "1" ANT "2" ANT "3" ANT "4" ANT "RX"
P3 1: 2: 3: 4: P4 0: 1:
ANT "1" ANT "2" ANT "3" ANT "4" ANT "RX" "OFF" ANT "RX" "ON"
A
N
P1 P3 P4
;
VFO-B TO VFO-A
1 2 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
B
1 1
A
2 2
;
3 3
AUTO NOTCH
1 2 3 3 4 4 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
B
1
C
2
P1 P2 P1
3
;
5 5
B
1
C
2
;
4
P1 0: Main (VFO-A) Band Receiver 1: Sub (VFO-B) Band Receiver P2 0: Auto Notch "OFF" 1: Auto Notch "ON"
B
1
C
2
P1 P2
3 4
;
5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
BAND DOWN B
1 1
D
2 2
P1
3 3
;
4 4
P1 0: Main (VFO-A) Band 1: Sub (VFO-B) Band
S-J220 SERIES CAT OPERATION REFERENCE
Page 4
CAT (COMPUTER AIDED TRANSCEIVER) OPERATION
CONTROL COMMAND TABLES
BI Set Read Answer BP Set Read Answer BS Set Read Answer BU Set Read Answer BY Set Read Answer CA Set Read Answer CH Set Read Answer CN Set Read Answer BREAK-IN
1 2 3 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
B
1
I
2
P1
3
;
4 4
P1 0: Break-in "OFF" 1: Break-in "ON"
B
1
I
2
;
3
B
I
P1
;
P1 0: Main (VFO-A) Band Receiver P3 When P2=0 1: Sub (VFO-B) Band Receiver 000: OFF P2 0: Manual NOTCH "ON/OFF" 001: ON 1: Manual NOTCH LEVEL When P2=1 001 - 400 (NOTCH Frequency : x 10 Hz )
MANUAL NOTCH
1 2 3 3 3 4 4 4 5 5 6 6 6 7 7 7 8 9 9 9 10 10 10
B
1
P
2
P1 P2 P3 P3 P3 P1 P2 ;
5
;
8 8
B
1
P
2
B
P
P1 P2 P3 P3 P3
;
P1 00: 1. 8 MHz 01: 3. 5 MHz 02: 03: 7 MHz 04: 10 MHz 05: 14 MHz 06: 18 MHz 07: 21 MHz 08: 24. 5 MHz 09: 28 MHz 10: 50 MHz 11: GEN
BAND SELECT
1 2 3 3 3 4 4 4 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
B
1 1
S
2 2
P1 P1
;
5 5
BAND UP
1 2 3 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
B
1 1
U
2 2
P1
3 3
;
4 4
P1 0: Main (VFO-A) Band 1: Sub (VFO-B) Band
BUSY
1 1 2 2 3 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
B
1
Y
2
;
3
P1 0: Main (VFO-A) Band BUSY "OFF" 1: Main (VFO-A) Band BUSY "ON" P2 0: Sub (VFO-B) Band BUSY "OFF" 1: Sub (VFO-B) Band BUSY "ON"
B
Y
P1 P2
;
CLASS-A
1 2 3 3 4 4 5 5 5 6 6 6 7 8 8 8 9 9 9 10 10 10
C
1
A
2
P1 P2 P2 P2 P1
3
;
7 7
C
1
A
2
;
4
C
A
P1 P2 P2 P2
;
P1 0:CLASS-A ON/OFF 1: BIAS LEVEL P2 When P1=0 000: OFF 001: ON When P1=1 001 - 100
CHANNEL UP/DOWN
1 2 3 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
C
1 1
H
2 2
P1
3 3
;
4 4
P1 0: Memory Channel "UP" 1: Memory Channel "DOWN"
CTCSS TONE FREQUENCY
1 2 3 3 4 4 5 5 5 6 7 7 7 8 8 8 9 9 9 10 10 10
C
1
N
2
P1 P2 P2 P1
3
;
6 6
P1 0: Main (VFO-A) Band Receiver 1: Sub (VFO-B) Band Receiver P2 0 - 49: Tone Frequency Number
C
1
N
2
;
4
C
N
P1 P2 P2
00 01 02 03 04 05 06 07 08 67. 0 Hz 69. 3 Hz 71. 9 Hz 74. 4 Hz 77. 0 Hz 79. 7 Hz 82. 5 Hz 85. 4 Hz 88. 5 Hz
; CTCSS TONE CHART
09 10 11 12 13 14 15 16 17 91. 5 Hz 94. 8 Hz 97. 4 Hz 100. 0 Hz 103. 5 Hz 107. 2 Hz 110. 9 Hz 114. 8 Hz 118. 8 Hz 18 19 20 21 22 23 24 25 26 123. 0 Hz 127. 3 Hz 131. 8 Hz 136. 5 Hz 141. 3 Hz 146. 2 Hz 151. 4 Hz 156. 7 Hz 159. 8 Hz 27 28 29 30 31 32 33 34 35 162. 2 Hz 165. 5 Hz 167. 9 Hz 171. 3 Hz 173. 8 Hz 177. 3 Hz 179. 9 Hz 183. 5 Hz 186. 2 Hz 36 37 38 39 40 41 42 43 44 189. 9 Hz 192. 8 Hz 196. 6 Hz 199. 5 Hz 203. 5 Hz 206. 5 Hz 210. 7 Hz 218. 1 Hz 225. 7 Hz 45 46 47 48 49 --------229. 1 Hz 233. 6 Hz 241. 8 Hz 250. 3 Hz 254. 1 Hz ---------
Page 5
S-J220 SERIES CAT OPERATION REFERENCE
CAT (COMPUTER AIDED TRANSCEIVER) OPERATION
CONTROL COMMAND TABLES
CO Set Read Answer CS Set Read Answer CT Set Read Answer DA Set Read Answer Set Read Answer DN Set Read Answer DP Set Read Answer DS Set Read Answer ED Set Read Answer CONTOUR
1 2 3 3 3 4 4 4 5 5 6 6 6 7 8 8 8 9 9 9 10 10 10
C
1
O
2
P1 P2 P3 P3 P1 P2 ;
5
;
7 7
C
1
O
2
C
1
O
2
P1 P2 P3 P3
3 4 5 5 5 6 6 6
;
7 7 7 8 8 8 9 9 9 10 10 10
P1 0: Main (VFO-A) Band Receiver P3 When P2=0, 1: Sub (VFO-B) Band Receiver 000: CONTOUR/APF "OFF" P2 0: CONTOUR/APF "ON/OFF" 001: CONTOUR "ON" 1: CONTOUR FREQUENCY 002: APF "ON" When P2=1, 01 - 40 (CONTOUR FREQUENCY) 100 ~ 4000 Hz
CW SPOT C
1
S
2
P1
3
;
4 4
P1 0: OFF 1: ON
C
1
S
2
;
3
C
S
P1
;
P1 0: Main (VFO-A) Band Receiver 1: Sub (VFO-B) Band Receiver P2 0: CTCSS "OFF" 1: CTCSS ENC/DEC "ON" 2: CTCSS ENC "ON"
CTCSS
1 2 3 3 4 4 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
C
1
T
2
P1 P2 P1
3
;
5 5
C
1
T
2
;
4
C
1
T
2
P1 P2
3 3 4 4 4 14 14 14
;
5 5 5 15 15 15 6 6 6 16 16 16 7 7 7 17 17 17 8 8 8 18 18 18 9 9 9 19 19 19 10 10 10 20 20 20
DIMMER
P1 00 - 15: VFD Backlight Brightness Level P3 00 - 15: OLE Brightness Level P4 00 - 15: ELCD (SM-5000) Brightness Level
D
1
A
2
P1 P1 P2 P2 P3 P3 P4 P4 P2 00 - 15: Meter Brightness Level ;
3 13 13 13
D
1
A
2
D
11
A
12 12 12
P1 P1 P2 P2 P3 P3 P4 P4
;
11 11
; MIC DWN
1 2 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
D
1 1
N
2 2
;
3 3
DISPLAY
1 2 3 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
D
1
P
2
P1
3
;
4 4
D
1
P
2
;
3
D
P
P1
;
P1 0: World Clock Display : This command does not acti1: Band Scope Display vates when the optional Data 2: AF Oscilloscope/Spectrum Analyzer Display Managemnt Unit is not attached. [. . . ] X O O O O O O O X O O O O O O O O O O O O O O O X O X O X O O O O O O X O O O O X O O O O O O O O O O X O O O O O O O O O O O O O X X X O X X O O O O O O O O X O O O O O O X O O O X O O O X O O O O O X O O O O O O O O O O O O O X X X O X X O O O O O O O O X O O O O O O X O O O X O O O X O O O AI X O X O O O O O X O O X O O O X X X X O X X O O O O O X O O X O O O O O O X O O O X O O O X O O O
Page 3
S-J220 SERIES CAT OPERATION REFERENCE
CAT (COMPUTER AIDED TRANSCEIVER) OPERATION
CONTROL COMMAND TABLES
AB Set Read Answer AC Set Read Answer AG Set Read Answer AI Set Read Answer AM Set Read Answer AN Set Read Answer BA Set Read Answer BC Set Read Answer BD Set Read Answer VFO-A TO VFO-B
1 2 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
A
1 1
B
2 2
;
3 3
ANTENNA TUNER CONTROL
1 2 3 3 4 4 4 5 5 5 6 7 7 7 8 8 8 9 9 9 10 10 10
A
1
C
2
P1 P2 P3 ;
3
;
6 6
P1 0: Fixed P2 0: Fixed
P3 0: Tuner "OFF" 1: Tuner "ON" 2: Tuning Start
A
1
C
2
A
C
P1 P2 P3
;
P1 0: Main (VFO-A) Band Receiver 1: Sub (VFO-B) Band Receiver P2 000 - 255
AF GAIN
1 2 3 3 4 4 5 5 5 6 6 6 7 8 8 8 9 9 9 10 10 10
A
1
G
2
P1 P2 P2 P2 P1
3
;
7 7
A
1
G
2
;
4
A
1
G
2
P1 P2 P2 P2
3 4 5 5 5 6 6 6
;
7 7 7 8 8 8 9 9 9 10 10 10
AUTO INFORMATION A
1
I
2
P1
3
;
4 4
P1 0: Auto Information "OFF" 1: Auto Information "ON" This parameter is set to "0" (OFF) automatically when the transceiver is turned "OFF. "
A
1
I
2
;
3
A
I
P1
;
VFO-A TO MEMORY CHANNEL
1 2 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
A
1 1
M
2 2
;
3 3
ANTENNA NUMBER
1 2 3 3 4 4 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
A
1
N
2
P1 P2 P1
3
;
5 5
P1 0: Main (VFO-A) Band 1: Sub (VFO-B) Band
A
1
N
2
;
4
P2 1: 2: 3: 4: 5:
ANT "1" ANT "2" ANT "3" ANT "4" ANT "RX"
P3 1: 2: 3: 4: P4 0: 1:
ANT "1" ANT "2" ANT "3" ANT "4" ANT "RX" "OFF" ANT "RX" "ON"
A
N
P1 P3 P4
;
VFO-B TO VFO-A
1 2 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
B
1 1
A
2 2
;
3 3
AUTO NOTCH
1 2 3 3 4 4 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
B
1
C
2
P1 P2 P1
3
;
5 5
B
1
C
2
;
4
P1 0: Main (VFO-A) Band Receiver 1: Sub (VFO-B) Band Receiver P2 0: Auto Notch "OFF" 1: Auto Notch "ON"
B
1
C
2
P1 P2
3 4
;
5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
BAND DOWN B
1 1
D
2 2
P1
3 3
;
4 4
P1 0: Main (VFO-A) Band 1: Sub (VFO-B) Band
S-J220 SERIES CAT OPERATION REFERENCE
Page 4
CAT (COMPUTER AIDED TRANSCEIVER) OPERATION
CONTROL COMMAND TABLES
BI Set Read Answer BP Set Read Answer BS Set Read Answer BU Set Read Answer BY Set Read Answer CA Set Read Answer CH Set Read Answer CN Set Read Answer BREAK-IN
1 2 3 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
B
1
I
2
P1
3
;
4 4
P1 0: Break-in "OFF" 1: Break-in "ON"
B
1
I
2
;
3
B
I
P1
;
P1 0: Main (VFO-A) Band Receiver P3 When P2=0 1: Sub (VFO-B) Band Receiver 000: OFF P2 0: Manual NOTCH "ON/OFF" 001: ON 1: Manual NOTCH LEVEL When P2=1 001 - 400 (NOTCH Frequency : x 10 Hz )
MANUAL NOTCH
1 2 3 3 3 4 4 4 5 5 6 6 6 7 7 7 8 9 9 9 10 10 10
B
1
P
2
P1 P2 P3 P3 P3 P1 P2 ;
5
;
8 8
B
1
P
2
B
P
P1 P2 P3 P3 P3
;
P1 00: 1. 8 MHz 01: 3. 5 MHz 02: 03: 7 MHz 04: 10 MHz 05: 14 MHz 06: 18 MHz 07: 21 MHz 08: 24. 5 MHz 09: 28 MHz 10: 50 MHz 11: GEN
BAND SELECT
1 2 3 3 3 4 4 4 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
B
1 1
S
2 2
P1 P1
;
5 5
BAND UP
1 2 3 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
B
1 1
U
2 2
P1
3 3
;
4 4
P1 0: Main (VFO-A) Band 1: Sub (VFO-B) Band
BUSY
1 1 2 2 3 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
B
1
Y
2
;
3
P1 0: Main (VFO-A) Band BUSY "OFF" 1: Main (VFO-A) Band BUSY "ON" P2 0: Sub (VFO-B) Band BUSY "OFF" 1: Sub (VFO-B) Band BUSY "ON"
B
Y
P1 P2
;
CLASS-A
1 2 3 3 4 4 5 5 5 6 6 6 7 8 8 8 9 9 9 10 10 10
C
1
A
2
P1 P2 P2 P2 P1
3
;
7 7
C
1
A
2
;
4
C
A
P1 P2 P2 P2
;
P1 0:CLASS-A ON/OFF 1: BIAS LEVEL P2 When P1=0 000: OFF 001: ON When P1=1 001 - 100
CHANNEL UP/DOWN
1 2 3 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
C
1 1
H
2 2
P1
3 3
;
4 4
P1 0: Memory Channel "UP" 1: Memory Channel "DOWN"
CTCSS TONE FREQUENCY
1 2 3 3 4 4 5 5 5 6 7 7 7 8 8 8 9 9 9 10 10 10
C
1
N
2
P1 P2 P2 P1
3
;
6 6
P1 0: Main (VFO-A) Band Receiver 1: Sub (VFO-B) Band Receiver P2 0 - 49: Tone Frequency Number
C
1
N
2
;
4
C
N
P1 P2 P2
00 01 02 03 04 05 06 07 08 67. 0 Hz 69. 3 Hz 71. 9 Hz 74. 4 Hz 77. 0 Hz 79. 7 Hz 82. 5 Hz 85. 4 Hz 88. 5 Hz
; CTCSS TONE CHART
09 10 11 12 13 14 15 16 17 91. 5 Hz 94. 8 Hz 97. 4 Hz 100. 0 Hz 103. 5 Hz 107. 2 Hz 110. 9 Hz 114. 8 Hz 118. 8 Hz 18 19 20 21 22 23 24 25 26 123. 0 Hz 127. 3 Hz 131. 8 Hz 136. 5 Hz 141. 3 Hz 146. 2 Hz 151. 4 Hz 156. 7 Hz 159. 8 Hz 27 28 29 30 31 32 33 34 35 162. 2 Hz 165. 5 Hz 167. 9 Hz 171. 3 Hz 173. 8 Hz 177. 3 Hz 179. 9 Hz 183. 5 Hz 186. 2 Hz 36 37 38 39 40 41 42 43 44 189. 9 Hz 192. 8 Hz 196. 6 Hz 199. 5 Hz 203. 5 Hz 206. 5 Hz 210. 7 Hz 218. 1 Hz 225. 7 Hz 45 46 47 48 49 --------229. 1 Hz 233. 6 Hz 241. 8 Hz 250. 3 Hz 254. 1 Hz ---------
Page 5
S-J220 SERIES CAT OPERATION REFERENCE
CAT (COMPUTER AIDED TRANSCEIVER) OPERATION
CONTROL COMMAND TABLES
CO Set Read Answer CS Set Read Answer CT Set Read Answer DA Set Read Answer Set Read Answer DN Set Read Answer DP Set Read Answer DS Set Read Answer ED Set Read Answer CONTOUR
1 2 3 3 3 4 4 4 5 5 6 6 6 7 8 8 8 9 9 9 10 10 10
C
1
O
2
P1 P2 P3 P3 P1 P2 ;
5
;
7 7
C
1
O
2
C
1
O
2
P1 P2 P3 P3
3 4 5 5 5 6 6 6
;
7 7 7 8 8 8 9 9 9 10 10 10
P1 0: Main (VFO-A) Band Receiver P3 When P2=0, 1: Sub (VFO-B) Band Receiver 000: CONTOUR/APF "OFF" P2 0: CONTOUR/APF "ON/OFF" 001: CONTOUR "ON" 1: CONTOUR FREQUENCY 002: APF "ON" When P2=1, 01 - 40 (CONTOUR FREQUENCY) 100 ~ 4000 Hz
CW SPOT C
1
S
2
P1
3
;
4 4
P1 0: OFF 1: ON
C
1
S
2
;
3
C
S
P1
;
P1 0: Main (VFO-A) Band Receiver 1: Sub (VFO-B) Band Receiver P2 0: CTCSS "OFF" 1: CTCSS ENC/DEC "ON" 2: CTCSS ENC "ON"
CTCSS
1 2 3 3 4 4 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
C
1
T
2
P1 P2 P1
3
;
5 5
C
1
T
2
;
4
C
1
T
2
P1 P2
3 3 4 4 4 14 14 14
;
5 5 5 15 15 15 6 6 6 16 16 16 7 7 7 17 17 17 8 8 8 18 18 18 9 9 9 19 19 19 10 10 10 20 20 20
DIMMER
P1 00 - 15: VFD Backlight Brightness Level P3 00 - 15: OLE Brightness Level P4 00 - 15: ELCD (SM-5000) Brightness Level
D
1
A
2
P1 P1 P2 P2 P3 P3 P4 P4 P2 00 - 15: Meter Brightness Level ;
3 13 13 13
D
1
A
2
D
11
A
12 12 12
P1 P1 P2 P2 P3 P3 P4 P4
;
11 11
; MIC DWN
1 2 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
D
1 1
N
2 2
;
3 3
DISPLAY
1 2 3 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
D
1
P
2
P1
3
;
4 4
D
1
P
2
;
3
D
P
P1
;
P1 0: World Clock Display : This command does not acti1: Band Scope Display vates when the optional Data 2: AF Oscilloscope/Spectrum Analyzer Display Managemnt Unit is not attached. KM CQ ~ ; ( space)
KEYER MEMORY
1 2 3 3 4 4 5 5 5 6 6 6 7 7 7 ~ 53
K
1
M
2
P1 P2 P2 P2 P2 P1
3
~
8 ~
P2
9 53
**
;
10
K
1
M
2
;
4
K
M
P1 P2 P2 P2 P2
~
P2
**
;
KEY PITCH
1 2 3 3 4 4 4 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
P1 00 ~75: 300 Hz ~ 1050 Hz (10 Hz Step)
K
1
P
2
P1 P1 ;
3
;
5 5
K
1
P
2
K
P
P1 P1
;
P1 0: KEYER "OFF" 1: KEYER "ON"
KEYER
1 2 3 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
K
1
R
2
P1
3
;
4 4
K
1
R
2
;
3
K
1
R
2
P1
3 3
;
4 4 4 5 5 5 6 7 7 7 8 8 8 9 9 9 10 10 10
KEY SPEED
P1 004 - 060 (WPM)
K
1
S
2
P1 P1 P1 ;
3
;
6 6
K
1
S
2
K
S
P1 P1 P1
;
P1 1: Keyer Memory "1" Playback 2: Keyer Memory "2" Playback 3: Keyer Memory "3" Playback 4: Keyer Memory "4" Playback 5: Keyer Memory "5" Playback 6: Message Keyer "1" Playback 7: Message Keyer "2" Playback 8: Message Keyer "3" Playback 9: Message Keyer "4" Playback A: Message Keyer "5" Playback
CW KEYING
1 2 3 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
K
1 1
Y
2 2
P1
3 3
;
4 4
LOCK
1 2 3 4 5 5 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
L
1
K
2
P1
3
;
4 4
L
1
K
2
;
3
P1 0: VFO A "OFF" (SET Only) 1: VFO A "ON" (SET Only) 2: VFO B "OFF" (SET Only) 3: VFO B "ON" (SET Only)
4: VFO A "OFF", VFO B "OFF" 5: VFO A "ON", VFO B "OFF" 6: VFO A "OFF", VFO B "ON" 7: VFO A "ON", VFO B "ON"
L
K
P1
;
Page 11
S-J220 SERIES CAT OPERATION REFERENCE
CAT (COMPUTER AIDED TRANSCEIVER) OPERATION
CONTROL COMMAND TABLES
LM Set Read Answer MA Set Read Answer MC Set Read Answer MD Set Read Answer MG Set Read Answer MK Set Read Answer ML Set Read Answer MR Set Read Answer LOAD MESSAGE
1 2 3 3 4 4 5 6 6 6 7 7 7 8 8 8 9 9 9 10 10 10
L
1
M
2
P1 P2 P1
3
;
5 5
P1 0: DVS 1: P. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE PIONEER S-J220
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual PIONEER S-J220 will begin.
