User manual PIONEER SX-550 schematic

[. . . ] The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. D3-4-2-1-1_En-A WARNING This equipment is not waterproof. To prevent a fire or shock hazard, do not place any container filed with liquid near this equipment (such as a vase or flower pot) or expose it to dripping, splashing, rain D3-4-2-1-3_A_En or moisture. WARNING Before plugging in for the first time, read the following section carefully. The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e. g. , 230V D3-4-2-1-4_A_En or 120V) written on the rear panel. Operating Environment Operating environment temperature and humidity: +5 ºC to +35 ºC (+41 ºF to +95 ºF); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light) D3-4-2-1-7c_A_En WARNING To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the D3-4-2-1-7a_A_En equipment. This product complies with the Low Voltage Directive (73/23/EEC, amended by 93/68/EEC), EMC Directives (89/336/EEC, amended by 92/31/EEC and D3-4-2-1-9a_En 93/68/EEC). CAUTION This product is a class 1 laser product, but this product contains a laser diode higher than Class 1. [. . . ] Note that when you use this feature, the previous recording made on that timer program will be replaced by the next one, regardless of whether you have watched it yet or not. You can also set the recorder so that it will adjust the recording quality to try and fit the recording on to the disc if it would not otherwise fit at the recording quality you set (see Optimized Rec on page 132 for more on this). Finally, if you set a timer recording to record to DVD but there isn't a recordable DVD loaded at the time of the recording, the Recovery Recording feature will automatically record the program to the HDD for you. This recorder is compatible with VPS (Video Programming System) and PDC (Program Delivery Control) systems used by many TV stations to ensure that a timer recording catches the whole program even when the program is not running to schedule. Up to eight timer programs can be set with VPS/PDC on. Important · A timer recording can't be set if there are already 32 timer programs waiting to be recorded. · Timer recording will not start if: ­ The recorder is already recording. ­ A disc is being initialized, finalized or unfinalized. · Timer recording will start when the operation preventing timer recording has finished. Start recording the current TV channel. Recording continues with playback paused. · Note that it may take up to 10 seconds for recording to start. PLAY 2 Press to start playback. You can also use the scan buttons ( / ), pause ( PAUSE) and stop ( STOP)--all without affecting the recording. STOP REC 3 Press to stop the recording. Tip · You can press PAUSE LIVE TV while the recorder is in standby to switch on and immediately start recording. After pressing PAUSE LIVE TV, it will take at least 10 seconds for the picture to change (during this time, all controls except the power button are inoperative). 8 ENTER 2 [Front panel] Press and hold for three seconds to lock the controls. The front panel display briefly shows LOCK. If any buttons are pressed on the remote or front panel, LOCK is briefly displayed again. · To unlock the recorder, press and hold STOP on the front panel (while the recorder is stopped) for three seconds until the display shows UNLOCK. Set the end time. ENTER 9 Select `Yes' to set the timer recording and exit, or `No' to go back to the Easy Timer Recording screen. · You can check the timer recording details you just set from the Schedule Area in the GUIDE Plus system; see The Schedule Area on page 68. Extending a timer recording in progress You can extend a timer recording beyond the programmed end time. This can be useful if a broadcast program overruns, for example. Canceling or extending the timer REC ì Press and hold for three seconds during a 1 timer recording. Recording continues, but the timer indicator disappears from the front panel display indicating that the timer has been canceled. REC ì Press repeatedly to extend recording in 30 2 minute blocks. 81 En 06 Recording PLAY Timer recording FAQ Frequently Asked Questions · Even though the timer is set, the recorder doesn't start recording!Check that the disc loaded or HDD is recordable, not locked (see Lock Disc on page 123), and that there are fewer than 99/999 titles already on the DVD/HDD. · The recorder won't let me enter a timer program!You can't enter a timer program if the clock isn't set. · What happens when two or more timer programs overlap? [. . . ] . Y: 1. 0 Vp-p (75 ) PB, PR: 0. 7 Vp-p (75 ) Jacks . AV connector 2 (Input 1) RGB output Output level. Input 2 (front) L/R Input level During audio input . . 2 V rms (Input impedance: more than 22 k) Jacks . [. . . ]