User manual PIONEER TS-W257D4

[. . . ] The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e. g. , 230 V D3-4-2-1-4_A_En or 120 V) written on the rear panel. WARNING To prevent a fire hazard, do not place any naked flame sources (such as a lighted candle) on the D3-4-2-1-7a_A_En equipment. If the AC plug of this unit does not match the AC outlet you want to use, the plug must be removed and appropriate one fitted. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. If connected to an AC outlet, the cut-off plug can cause severe electrical shock. [. . . ] 5 If you selected `Advanced EQ Setup', input the time setting you want to use for calibration, then select `Go'. Select `Start' from the next screen. Based on the reverb measurement above, you can choose the time period that will be used for the final frequency adjustment and calibration. Even though you can make this setting without reverb measurement, it is best to use the measurement results as a reference for your time setting. For an optimal system calibration based on the direct sound coming from the speakers, we recommend using the 30~50ms setting. 3e4. dB Adv. EQ Setup (1/2) Ch [ L ] Fq [ 63Hz ] Tm [60~80ms] 3e4. Adv. EQ Setup (2/2) ( Back ) 3 If you selected `Reverb Measurement', select EQ ON or OFF and then OK. 3e1. Reverb Measurement MCACC: M1. MEMORY 1 Measure with Setting Start?MEMORY 1 Ambient Noise Microphone Speaker Level Delay Check Reverb EQ:ON [ OK ] [ ] [ ] [ ] [ ] :Cancel 3e1. Reverb Measurement Now Analyzing . . . (1/5) EQ Type [ALL CH ADJUST] Multi-Point NO Setting Start?[OK] 0 80 160ms ( Next) :Cancel : Cancel :Cancel Use the / buttons to select the channel, frequency, and time setting. Use the / buttons to switch between them. Make sure you don't overwrite an MCACC preset you're currently using (this can't be undone). 3 Select `Copy' to confirm and copy the settings. shows in the OSD to confirm the MCACC preset has been copied, then you automatically return to the Data Management setup menu. :Return ENTER:Next :Return Note 1 This can be done in Automatically setting up for surround sound (Auto MCACC) on page 8 or Automatic MCACC (Expert) on page 37, either of which you should have already completed. 2 The settings made in Automatically setting up for surround sound (Auto MCACC) on page 8 or Automatic MCACC (Expert) on page 37. 45 En 08 The System Setup menu Renaming MCACC presets If you have several different MCACC presets that you're using, you may want to rename them for easier identification. 1 Select `Memory Rename' from the Data Management setup menu. 4. Data Management a. MCACC b. MCACC c. Memory d. Memory Data Check Data Copy Rename Clear 4c. Memory Rename MCACC Position Rename M1 M2 M3 M4 M5 M6 [ [ [ [ [ [ MEMORY MEMORY MEMORY MEMORY MEMORY MEMORY 1 2 3 4 5 6 ] ] ] ] ] ] :Finish These settings are designed to customize your system, but if you're satisfied with the settings made in Automatically setting up for surround sound (Auto MCACC) on page 8, it isn't necessary to make all of these settings. Caution · The test tones used in the System Setup are output at high volume. 1 Select `Manual SP Setup' then press ENTER. System Setup 1. Auto MCACC 2. Surr Back System 3. Manual MCACC 4. Data Management 5. Manual SP Setup 6. Input Setup 7. Other Setup : Exit 5. Manual SP Setup a. Speaker Setting b. Channel Level c. Speaker Distance d. X-Curve e. THX Audio Setting :Return 2 Select the MCACC preset you want to rename, then select an appropriate preset name. Use / to select the preset, then / to select a preset name. 3 Repeat for as many MCACC presets as necessary, then press RETURN when you're finished. You will return to the Data Management setup menu. :Return 2 Select the setting you want to adjust. If you are doing this for the first time, you may want to adjust these settings in order: · Speaker Setting ­ Specify the size and number of speakers you've connected (see below). · Channel Level ­ Adjust the overall balance of your speaker system (page 47). · Speaker Distance ­ Specify the distance of your speakers from the listening position (page 48). [. . . ] 15. 3 kg Furnished Parts Setup microphone (for Auto MCACC setup). 1 These operating instructions Composite Video / S-Video Section Input (Sensitivity/Impedance) . . 5 Hz to 10 MHz Note · Specifications and the design are subject to possible modifications without notice, due to improvements. Component Video Section Input (Sensitivity/Impedance) . . 5 Hz to 100 MHz Cleaning the unit · Use a polishing cloth or dry cloth to wipe off dust and dirt. [. . . ]