User manual PIONEER VSX-2020-K

[. . . ] Please write this serial number on your enclosed warranty card and keep it in a secure area. This is for your security. THE STANDBY/ON BUTTON IS SECONDARY CONNECTED AND THEREFORE DOES NOT SEPARATE THE UNIT FROM MAINS POWER IN STANDBY POSITION. IMPORTANT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. [. . . ] Then go back and leave the level setting at a point just before that. Press the ENTER button and the receiver will remember this bass output level. To exit before outputting the TEST TONE select EXIT and press the ENTER button. To exit while outputting the TEST TONE press the ENTER button. S-VIDEO PHONES VIDEO INPUT VIDEO L AUDIO R MULTI CH INPUT TONE CHANNEL SELECT LOUDNESS DIGITAL NR SIGNAL SELECT FL DIMMER CLASS BAND - TUNING + SPEAKERS - BASS + - TREBLE + VIDEO SELCT TAPE 2 MONITOR MPX TUNER CONTROL MEMORY - STATION + MIN MAX MASTER VOLUME memo If you select SETTING CANCEL no settings are input to the receiver but the screen remains on the TV. To escape the screen you must select EXIT and press the ENTER button. 3 Select EXIT and press the ENTER button to return to the SYSTEM SETUP MENU. This completes the speaker setup. 38 Initial Set Up Dynamic Range Control This feature makes it possible to enjoy full surround sound effects on Dolby Digital sources even at low volumes. It does this by compressing the dynamic range. Dynamic range is the difference between the loudest and the softest sounds in any given signal. Compressing the range plays sounds so the quieter ones are audible and the louder ones don't get distorted or become overpowering. This feature only applies to Dolby Digital sources but the MIDNIGHT LISTENING mode accomplishes the same end for a variety of sources (see page 49). If continuing from Bass Peak Level go to step 1. If starting fresh, complete steps 1-3 in "Setting Up for Surround Sound" (p. 29) first. Î S0URCE MULTI OPERATION SYSTEM OFF USE SETUP RECEIVER DVD/LD TV/SAT VCR1 VCR2 MULTI CONTROL CD CLASS MD/ TAPE1 MPX TUNER BAND TVCONT DIRECT ACCESS 1 Select D-RANGE CONTROL (if continuing from BASS PEAK LEVEL, it will already be selected). See "Setting Up for Surround Sound" on page 29 if you are unsure how to do this. In STEREO mode only the front two speakers, and sometimes the subwoofer (if you have one), are used. STANDARD mode This mode is for pure decoding of Dolby Digital, Dolby Pro Logic or DTS sources. It is good for enjoying regular movies/videos that have been recorded in Dolby Digital, Dolby Pro Logic or DTS. STANDARD 7. 1 is also the basic mode for enjoying sources with SURROUND BACK channels. For more detailed information see p. 83-84. You will only be able to access the second two modes if you have hooked up SURROUND BACK speaker(s). For more detailed information see p. 19, 32-33. The display will show you what kind of source (Dolby Digital, DTS, etc. ) is being played. STANDARD Use this mode with sources that do not have SURROUND BACK channels. If you don't have SURROUND BACK speaker(s) switched on (see p. 32-33) this is the only STANDARD mode you will be able to select on the receiver. STANDARD 7. 1 This mode is best for sources with SURROUND BACK channels. You will only be able to access this mode if you have set the SURROUND BACK speakers in the SPEAKER SETUP procedure (see p. 32-33). Also, this mode will play 5. 1 channels sources and other sources through all the speakers you have hooked up, routing some of the sound into your SURROUND BACK channel or channels. STANDARD 7. 1 will appear in the display even if you only have one SURROUND BACK speaker hooked up. [. . . ] ** Measured by Audio Spectrum Analyzer. 90 Techno Tidbits & Problem-solving Furnished Parts FM wire Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 AM loop Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 "AA" IEC LR6 batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Remote Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]