User manual PIONEER VSX-2021

[. . . ] VSX-LX55 VSX-202 1-K IMPORTANT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel. IMPORTANT: THE MOULDED PLUG This appliance is supplied with a moulded three pin mains plug for your safety and convenience. [. . . ] Adjusts the red/green balance. RES (Resolution) <b> Specifies the output resolution of the video signal (when video input signals are output at the HDMI OUT connector, select this according to the resolution of your monitor and the images you wish to watch). ("576p" indicates the 480p/576p resolution setting. ) PURE 576p 720p 1080i 1080p 1080/24p AUTO ON OFF c ­4 to +4 d Default: 0 Adjusts saturation from dull to bright. Sets the black level according to the video input signal. If the black level is too bright due to the combination with the connected monitor, select 7. 5. PCINEMA (PureCinema) <c, e> This setting optimizes the operation of the progressive scanning circuit for playing film materials. If the picture seems unnatural, switch this to ON or OFF. THROUGH Specifies the aspect ratio when input signals are output at the HDMI output. Make your desired settings while checking each setting on your display (if the image doesn't match your NORMAL monitor type, cropping or black bands appear). P. MOTION Adjusts the motion and still picture quality when video (Progressive Motion) output is set to progressive. <c, e> 50 En a If the video picture deteriorates when this settings is switched ON, switch it OFF. When set to a resolution with which the TV (monitor) is not compatible, no picture is output. Also, in some cases no picture will be output due to copyright protection signals. When AUTO is selected, the resolution is selected automatically according to the capacity of the TV (monitor) connected by HDMI. When PURE is selected, the signals are output with the same resolution as when input (see About the video converter on page 16 ). If this is set to something other than AUTO, PURE and 480i/576i analog signals are input, 480p/576p signals are output from the component output terminals. Using other functions 09 c !This setting is valid for component outputs and HDMI output. P. MOTION is disabled when PCINEMA is set to ON. This setting have the effect only for pictures recorded in the interlaced scan format (480i/576i or 1080i signals). d Adjustment is not possible unless V. ADJ (Advanced Video Adjust) is set to MEMORY. This setting is only displayed when the video signals below are being input: -- 480i, 576i, 480p, 576p, 720p, 1080i analog video signals -- 480i, 576i, 480p, 576p, 720p, 1080i, 1080p, 1080p24 HDMI video signals f This adjustment is only possible when 480i signals are being input from the composite video jacks. If the image doesn't match your monitor type, adjust the aspect ratio on the source component or on the monitor. This setting is only displayed when 480i/p or 576i/p video signals are being input. Switching the speaker terminals If you selected Normal(SB/FH), Normal(SB/FW) or Speaker B at Speaker system setting on page 67 , you can switch between speakers using the SPEAKERS button. If you selected Front Bi-Amp or ZONE 2, the button will simply switch your main speaker terminals on or off. % Use SPEAKERS on the front panel to select a speaker system setting. As mentioned above, if you have selected Front Bi-Amp or ZONE 2, the button will simply switch your main speaker terminal (A) on or off. Press repeatedly to choose a speaker terminal option: When you select Normal(SB/FH), you can select from: !SP: SB/FH ON ­ Surround back or front height channels are added to the front, center and surround channels (maximum 5 channels) and a maximum of 7 channels are output. [. . . ] Specifications and the design are subject to possible modifications without notice, due to improvements. This product includes FontAvenue® fonts licensed by NEC Corporation. FontAvenue is a registered trademark of NEC Corporation. Network Section LAN terminal . . . . . . . . . . . . . . . . . 10 BASE-T/100 BASE-TX Miscellaneous Power requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 220 V to 230 V, 50 Hz/60 Hz Power consumption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 570 W In standby . . . . . . . . . . . . . [. . . ]