User manual PIONEER VSX 924

[. . . ] Operating Instructions AV Receiver VSX- 924 -K/-S CAUTION TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Operating Environment D3-4-2-1-1_B1_En WARNING Operating environment temperature and humidity: +5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH (cooling vents not blocked) Do not install this unit in a poorly ventilated area, or in locations exposed to high humidity or direct sunlight (or strong artificial light). D3-4-2-1-7c*_A2_En Information for users on collection and disposal of old equipment and used batteries Symbol for equipment These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points in accordance with your national legislation. Symbol examples for batteries By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. [. . . ] If the image doesn’t match your monitor type, adjust the aspect ratio on the source component or on the monitor. This setting is only displayed when 480i/p or 576i/p video signals are being input. 0 d (The image is only an example for checking the effect. ) 70 09 Switching the output (OUTPUT PARAMETER) You can press OUT P. to switch the output of speaker terminals or HDMI terminals to be played. Using other functions Switching the HDMI output Set which terminal to use when outputting video and audio signals from the HDMI output terminals. The HDMI OUT 1 terminal is compatible with the Control with HDMI function. 　 　 　 　 Switching the speaker terminals If you selected Normal(SB/FH), Normal(SB/FW) or Speaker B at Speaker system setting on page ​ 9​ you can 8 , switch between speakers using the OUT P. If you selected Front Bi-Amp, ZONE 2 or HDZONE, the button will simply switch your main speaker terminals on or off. 1 Press OUT P. . 2 Use i/j to select ‘OUT 1/2’. 3 Use k/l to select the setting. Please wait a while when Please wait . . . The output switches among OUT 1+2, OUT 1, OUT 2 and OFF each time the button is pressed. ! The synchronized amp mode is canceled when the HDMI output is switched. If you wish to use the synchronized amp mode, switch to OUT 1, then select the synchronized amp mode on the TV using the TV’s remote control. ! When MAIN/HDZONE is set to HDZONE, it is not possible to switch to OUT 2 (page ​ 4​ . 9 ) 1 Press OUT P. . ! You can perform the same operation by pressing SPEAKERS on the front panel. 2 Use i/j to select ‘SP’. 3 Use k/l to switch the speaker terminals to be played. As mentioned above, if you have selected Front Bi-Amp, ZONE 2 or HDZONE, the button will simply switch your main speaker terminal (A) on or off. Press repeatedly to choose a speaker terminal option: When you select Normal(SB/FH), you can select from: ! SP: SB/FH ON – Surround back or front height channels are added to the front, center and surround channels (maximum 5 channels) and a maximum of 7 channels are output. The surround back and front height channels are switched automatically according to the audio input signal. ! SP: SB ON – Surround back channels are added to the front, center and surround channels (maximum 5 channels) and a maximum of 7 channels are output. ! SP: FH ON – Front height channels are added to the front, center and surround channels (maximum 5 channels) and a maximum of 7 channels are output. ! SP: OFF – No sound is output from the speakers. When you select Normal(SB/FW), you can select from: ! SP: SB/FW ON – Surround back or front wide channels are added to the front, center and surround channels (maximum 5 channels) and a maximum of 7 channels are output. The surround back and front wide channels are switched automatically according to the audio input signal. ! SP: SB ON – Surround back channels are added to the front, center and surround channels (maximum 5 channels) and a maximum of 7 channels are output. ! SP: FW ON – Front wide channels are added to the front, center and surround channels (maximum 5 channels) and a maximum of 7 channels are output. ! SP: OFF – No sound is output from the speakers. [. . . ] FontAvenue is a registered trademark of NEC Corporation. ! iOS is a trademark on which Cisco holds the trademark right in the US and certain other countries. ! Microsoft, Windows, Windows Media and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. ! Android and Google Play are trademarks of Google Inc. [. . . ]