User manual PIONEER XR-P60C

[. . . ] For more information on the DJS Software End User License Agreement, its minimum operating environment, installation procedures, and the Operating instructions (PDF file) please refer to the section, "ABOUT DJS SOFTWARE" in your XR-P60C Operating instructions. Table of Contents Chapter 1 Controlling DJS 1-1 Connecting to your XR-P60C to a computer . 3 4 5 6 7 Chapter 2 Upgrading XR-P60C 2-1 User Registration . 10 Copying of copyrighted materials such as music is unlawful unless permitted by a legal exception or consented to by the rightowners. is protected by the copyright laws of each country, as well as by international agreements. [. . . ] Set the mixing parameters. · Use the function buttons, select UP button, and select DOWN button to set up mixing. Functions that are Linked with the [DJ Play] Screen (Mix Functions) XR-P60C Operation Buttons Function [CUT-IN] Function [ZIP] Function [ECHO] Function [CROSS FADE] Function [BPM SYNC] Select UP Button Select DOWN Button Functions that are Linked with the [DJ Play] screen MIX Mode : CUT-IN MIX Mode : ZIP MIX Mode : ECHO MIX Mode : CROSS FADE The playback speed for the slave is merged to that of the master. BEAT ADJUST : Player A BEAT ADJUST : Player B When using an external mixer Only the BPM sync function can be used when the DJS mixer is set to an external mixer. Note Master & Slave The first player that starts playing is the master, the other player becomes the slave. The master and slave switch roles under the following circumstances. When the cross fader is moved all the way to the slave side When the master is paused while both players are playing together When the song on the master is changed while both players are playing together BEAT Adjust (Player A - Player B) While listening to the song being played, set the beat location. Set the effect parameters. · Use the function buttons, LOAD A button, LOAD B button, select UP and select DOWN buttons to make the settings. Functions that are Linked with the [DJ Play] Screen (Effect Functions) XR-P60C Operation Buttons Function [INPUT SELECT] Function [DELAY / ECHO] Function [PAN / TRANS] Function [FILTER / FRANGER] Function [REVERB / PITCH] Function [AUTO / TAP] LOAD A Button LOAD B Button Select UP Button Select DOWN Button Functions that are Linked with the [DJ Play] screen Switches Channels : Channel A, Channel B, Master Select Effect : Delay / Echo Select Effect : Pan / Trans Select Effect : Filter / Franger Select Effect : Reverb / Pitch Switches BPM Display : AUTO / TAP TAP Input TAP Input Effect Beat : Down Effect Beat : Up Note Channel Switching Select the channel for applying the sound effects, from among channel A, channel B and the master. Effect Selection You can select from the eight kinds of effects that are assigned to the four function buttons. BPM Display Switch You can select a BPM (beat per minute) display that is either AUTO or TAP. BPM (AUTO) The BPM value that is detected in the song on the selected channel is displayed. BPM (TAP) When you press either the LOAD A or LOAD B button twice or more in succession, the interval between presses is displayed as the BPM. 3 Operating with the Rotary Selector · If you rotate the rotary selector, you can adjust the level and depth of effects (balance between the original music on the selected channel and the sound effect of the selected effect). · If you press the rotary dial, the effect comes ON and the sound effect is output on the selected channel. Pressing it again makes the effect go OFF. Effect Beat The cycle (timing) of the sound effects, such as reverb, transition and echo, is set based on the displayed BPM. This cycle (timing) can be adjusted using the select UP or the select DOWN buttons. However, if the pitch is selected in the effect selection, you can use the select UP or select DOWN buttons to adjust the pitch. DJS Ver. 1. 601 7 2 Chapter 2 Upgrading XR-P60C The software that is originally incorporated into hardware products such as the XR-P60C and is used to control the hardware is called firmware. In order to download the update package and run the update program, connect your computer to the internet and Log on as a user who has been set up as a computer administrator. Before Updating the Version of the Firmware If you have not complete the user registration process, you will not be able to run the updater for your XR-P60C. Consequently, please complete user registration. `2-1 User Registration' Before starting up DJS, connect your XR-P60C and your computer with an auxiliary USB power cable and then connect the XR-P60C and the computer with a USB cable. `1-1 Connecting to your XR-P60C to a computer' Warning! In Windows Vista Follow the steps below to make the administrator settings. Log on as a user who has been established as the administrator for the computer. Right click the [DJS] shortcut icon on the desktop and then click on [Properties]. Click the [Compatibility] tab in the [DJS Properties]. Click on [Run this program as the administrator. ] so the check box is ON. Click [OK] and then close the [DJS Properties] window. When you have two or more XR-P60Cs It is not possible to update more than one XR-P60C at a time. So please connect one unit to your computer at a time. Before connecting your XR-P60C It is necessary to install driver software on your computer. [. . . ] `Offline Registration (Entering the Registration ID)' 10 DJS Ver. 1. 601 3 Addressing the User Registration Card The addresses for user registration cards are as follows. Please take care to use the address appropriate to where you live as each region has its own address. North America PIONEER ELECTRONICS (USA) INC. [. . . ]