User manual PLANAR EL240.128.45

[. . . ] EL240. 128. 45 ICEBriteTM EL Small Graphics Display USER'S MANUAL www. planar. com Revision Control Date August 2000 June 2004 September 2005 May 2010 Description Document number OM320-00 Document number 020-0345-00A Document number 020-0345-00B Document number 020-0345-00C Contents EL240. 128. 45 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation and Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Mounting EL Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Use a screen saver or image inversion to avoid causing burn-in on the display. 4 EL240. 128. 45 Operations Manual (020-0345-00C) Specifications The EL panel is a matrix structure with column and row electrodes arranged in an X-Y formation. Light is emitted when an AC voltage of sufficient amplitude is applied at a row-column intersection. The display operation is based on the symmetric, line-at-a-time data addressing scheme. Power The supply voltages are shown in Table 1. All internal high voltages are generated from the display supply voltage (VH). The logic supply voltage (VL) should be present whenever video input signals are applied. The minimum and maximum specifications in this manual should be met, without exception, to ensure the long-term reliability of the display. Performance characteristics are guaranteed when measured at 25 °C with rated input voltage unless otherwise specified. Planar does not recommend operation of the display outside these specifications. Table 1. Description Input voltage (nom=12. 0 V) Input voltage absolute max. Input current (VH =12. 0 V) Logic voltage (nom=5. 0 V) Logic voltage absolute max. Logic current Power consumption @ 120 Hz Power consumption @ 240 Hz *15 % of pixels on per row CAUTION: Absolute maximum ratings are those values beyond which damage to the device may occur. Na me VH VH max IH VL VL max IL Min 8 --4. 75 -0. 5 -3. 1 5. 8 90 5. 5 10. 9 0. 95 5. 25 6. 0 Typ* (W) Max 18. 0 19. 0 Absolut e Max Units Vdc Vdc Adc Vdc Vdc mAdc W W EL240. 128. 45 Operations Manual (020-0345-00C) 5 Figure 1. ON-pixels @ 120 Hz 100 90 80 70 Relative power (%) 60 50 40 30 20 10 0 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% ON-pixels Table 2. Description Absolute Input Voltage Range Low-level input voltage HIgh-level input voltage (except SEL1) HIgh-level input voltage SEL1 Logic input current* IL Symbo l VI max VIL VIH Min -0. 3 0 0. 5 x VL 0. 8 x VL ­ Max VL + 0. 3 0. 2 x VL VL VL ±10 (-2000) µA Units V V V * Signals /WR, /CS, SEL1, /RD, SELFTEST, /RES have pullup resistors (4. 7 k) 6 EL240. 128. 45 Operations Manual (020-0345-00C) Connector Video signals and DC power are supplied to the display through a single 24-pin, dual-row, 2 mm pitch square pin, right-angle, locking connector: Samtec part number EHT-112-01-S-D-RA, or an equivalent connector matching the pinouts in Table 3. The mating connector is the Samtec TCSD family of cable strips. Consult your Samtec representative (1-800SAMTEC9) for cable and connector options. (Back of display) (Viewed from top of connector) Key Pin 1 Pin 2 J1 Pin 1 (Bottom of display) Figure 2. Data/Power Connector ­ J1. Table 3. Connector Pinouts J1. Pin Signal Description Pin Signal Description 1 3 5 7 9 11 13 15 17 19 21 23 VH GND VL (+5 V) /WR /CS SELFTES D0 D2 D4 D6 SEL1 GND Display voltage Ground Logic voltage Write Chip Select input/output input/output input/output input/output Select Ground 2 4 6 8 10 12 14 16 18 20 22 24 VH(+12 V) GND RES /RD A0 GND D1 D3 D5 D7 READY LUMA Ground Reset Read Address Ground input/output input/output input/output input/output Display ready Luminance control EL240. 128. 45 Operations Manual (020-0345-00C) 7 Interface Information This Small Graphics Display (SGD) incorporates an interface that is compatible with the 8-bit microprocessor interfaces found in comparable LCD displays with built-in controllers. When high, display operates in SELFTEST mode Pin 5: +5 V logic supply voltage Pins 1 and 2: +12 V supply for DC-DC converter and display analog circuits Pin 24: Luminance control input Pins 3, 4, 12, and 23: Signal return for logic and power supplies /RD or E /WR or R//W /RES READY /CS A0 SELFTEST VL (+5V) VH(+12V) LUMA GND 8 EL240. 128. 45 Operations Manual (020-0345-00C) Video Input Signals Figure 3. 8080 Video Input Timing Diagram. Table 5. Signal A0, CS WR, RD Symbol tAH8 tAW8 tCYC tCC tDS8 tDH8 tACC8 tOH8 Tr, Tf Parameter min Address hold time Address setup time System cycle time Strobe pulsewidth Data setup time Data hold time RD access time Output disable time Input rise and fall times 10 0 550 120 120 5 10 max 50 50 30 unit ns ns ns ns ns ns ns ns ns Condition CL=100 pF D0 to D7 All signals EL240. 128. 45 Operations Manual (020-0345-00C) 9 Figure 4. 6800 Video Input Timing Diagram. Table 6. [. . . ] Conditions resulting from normal wear and tear and Buyer's failure to properly store, install, operate, handle or maintain the Goods are not within this warranty. Repair or replacement of Goods is Seller's sole obligation and Buyer's exclusive remedy for all claims of defects. If that remedy is adjudicated insufficient, Seller shall refund Buyer's paid price for the Goods and have no other liability to Buyer. All warranty repairs must be performed at Seller's authorized service center using parts approved by Seller. [. . . ]