User manual PLANAR GX3MP Product Manual

[. . . ] Transport and storage 12, 000 meters (39, 400 feet), maximum in unpressurized container Relative Humidity. Transport and storage 5% to 90% (non-condensing). Transport and storage -10° to 60° C. 2 Before You Begin The 21-inch Planar GX3MP grayscale display provides resolutions of 1536 x 2048 pixels in portrait mode and 2048 x 1536 pixels in landscape mode. Check that your system meets these requirements for installation of the Planar GX3MP display system. System Requirements · Intel Pentium 4/Xeon, AMD Athlon 64/K7/XP, or compatible · PCI Express x16 lane slot · 50 MB hard disk space · 256 MB RAM · CD-ROM drive · Power supply, 350 watts or greater Operating System Windows XP Service Pack 2 or Windows 2000 Service Pack 4 Safety Precaution Warning Advertencia Avertissement Warnung Avvertenza Wear an antistatic heel or wrist strap when installing the video card to avoid damage to computer components. 3 Unpacking the Display Check the contents of your Planar GX3MP display package for all the items shown here. [. . . ] When installing multiple graphics cards, install all cards before you install the driver. 7 Making the Connections Use only the DVI cable and power cord supplied with your Planar GX3MP display. To connect the display 1 Plug one end of the DVI cable into the DVI connector port. Tighten the thumbscrews to secure the connection. 2 Plug the power cord into the power input port. 3 Plug the other end of the DVI cable into DVI port 1 (the bottom port) on the installed graphics card. 4 Plug the other end of the power cord into a grounded outlet. 5 Power on your display first, then the computer. Power cord DVI cable 8 Use DVI port 1 (the bottom port) to connect a single display to the graphics card or to install the primary display of a dual configuration. DVI cable DVI port 1 AX3 graphics card installed 9 Installing the Display Driver Before you install the driver, remove any previously installed display driver for the graphics card from your system. To install the driver 1 Start the system. Click Cancel on the Found New Hardware Wizard dialog. Click No when the system prompts you to restart the computer. 2 Insert the driver installation CD and run Setup. exe . 5 Follow the onscreen instructions to complete the installation. Planar recommends that you select the Express installation option. 6 When the Setup complete message appears, select Yes, I want to restart my computer now and click Finish. 7 If the Digital Signature Not Found message appears, click Yes or Continue to complete the driver installation. To set the display mode manually 1 Right-click the desktop and select Properties > Settings. 2 Select the monitor that you want to change. Make sure that the check box for Hide modes that this monitor cannot display is empty (unchecked). 4 Click the Adapter tab, then click the List All Modes button. Then click Apply or OK. 10 To configure the display 1 Right-click the desktop and select Properties > Settings. 2 Select the native resolution of the display. Click OK. To use a dual-display configuration 1 Right-click the desktop and select Properties > Settings. Select Extend my Windows desktop onto this monitor. 3 Set the resolution and color quality for the second display. Click OK. Display Brightness Install the brightness control application located on the driver CD. [. . . ] Details of DIN connector VCC 8 VCC 7 VCC 6 VCC 5 4 GND 1 GND 2 GND 3 GND LED Status Lights LED A describes the digital-link status between the display controller and the interface. LED B describes the display-panel status. It shows any faults currently in the panel. A B 16 Power-up sequence information from LED LED A Action/Sequence LED B Dark Initial power-on Flashing yellow Blink yellow Self test Solid yellow Dark One (1) second after Flashing green power-on Action/Sequence Initial power-on Power-on self test Self test pass LED A status information after initial power-on LED Status Description Solid green Functional link ­ normal operation Flashing yellow Link working, unrecognized sync information Solid yellow Receiving DDC information LED B status information after initial power-on LED Status Description Solid green Functional system ­ normal operation Flashing green Fault Solid yellow DDC power-on, 12V power not detected Alternating green/yellow POST failure 17 U. S. FCC Compliance Statement This device complies with Part 15 of the FCC Rules. [. . . ]