User manual PLANAR PDP43P Product Manual

[. . . ] PDP-50P AND PDP-43P OPERATING INSTRUCTIONS This unit has been designed for use as a computer display monitor. The optional video card is required if you wish to view other video signals on the monitor. For details consult your local retail dealer. Contents related to system specifications, power requirements, accessories, and other information differ with respect to the country where this unit is purchased. Operating Instructions Thank you very much for purchasing this Planar product. Before using your Plasma Display, please read the "Safety Precautions" and these "Operating Instructions" carefully so you will know how to operate the Plasma Display properly. [. . . ] Input changes each time the main unit's INPUT is pressed as follows. 3 INPUT1 INPUT2 2 Before you begin, make sure you have: · Made connections between this unit and personal computer as described in the section "Installation and Connections" starting on page 10. · Set up the on-screen menu to input signals from components connected to INPUT1 and INPUT2 as described in the section "Setting Up the System" on page 17. If no connections are made to these terminals, on-screen setup is not necessary. · When the menu screen is displayed, changing the signal input will cause the menu screen to turn off. · If the input computer signal is not supported by the display, the following message will be displayed: I NPUT 1 CA U T I O N U N S UP P O R T E D S I G N AL fH: fV: 7 7. 0 H z 1 15 2X 864 FUL L 2, 5 2, 5 3 I NPUT 1 3 CA U T I O N OU T OF R A N G E f H : 7 5. 0 H z ­­­­ FUL L 4 Main Unit Operating Panel Remote Control Unit 4 Use VOLUME +/­ on the remote control unit to adjust the volume. If no audio connections are made to this unit, this step is not necessary. When viewing is finished, press STANDBY/ON to put the unit in standby mode. The STANDBY/ON indicator will blink and then remain lit (red) indicating that the standby mode is engaged. Operation is not possible while the STANDBY/ON indicator is blinking (red). Switch MAIN POWER on the main unit to the off position to turn the main power off. The STANDBY/ON indicator may continue to light for a short while even after the main power is turned off. This is a result of residual electric load impressed on the circuitry, and the light will turn off presently. 5 1 Switch MAIN POWER on the main unit to the on position to turn the main power on. Press STANDBY/ON to put this unit in the operation mode. The STANDBY/ON indicator turns green. 2 6 CAUTION Please do not leave the same picture displayed on the screen for a long time. Doing so may cause a phenomenon known as "screen burn" which leaves a ghost, or residual, image of the picture on the screen. 19 En Operations English 3 Operations English To adjust the volume To confirm display settings DISPLAY VOLUME +/­ Press VOLUME on the remote control unit. Use VOLUME + or VOLUME ­ to adjust the volume of the connected speakers. Press DISPLAY on the remote control unit. The currently selected input, screen size and refresh rates will be displayed for about 3 seconds. I NPUT 1 V O L U ME : 5 Operations To mute the sound fH: fV: 3 1. 0 H z 64 0X 480 D O T BY D OT MUTING Note The displayed refresh rates may be slightly different from actual values. Press MUTING on the remote control unit. Press MUTING again to restore the sound. Muting is automatically canceled about 8 minutes after the button is pressed, and the volume level is adjusted to the minimum level. Press VOLUME + or VOLUME ­ to adjust the volume at a desired level. 20 En Operations During personal computer signal input 1 DOT BY DOT The input signal and the screen maintain a dot to line ratio of 1:1 and is thus highly faithful to the source. [PDP-50P] Screen Size Selection This unit incorporates screen modes of various height and width ratios. For optimal viewing, we recommend that you select the screen mode that best matches the video source that you are viewing. Although these modes are designed for full display of a picture on a wide screen, it is our hope that you make use of them with a full understanding of the manufacturer's intentions. Changing the screen size The size of the image displayed on the screen, and the range of the image shown can be set in one of four modes on the PDP-50P, and in three modes on the PDP-43P. A 640 dots 1280 dots 480 lines 768 lines Press SCREEN SIZE to select the size. The screen size changes each time SCREEN SIZE is pressed as follows. [. . . ] 2 ÷ Due to improvements, specifications and design are subject to change without notice. Additional Information Input/output Video INPUT 1 Input Mini D-sub 15 pin (socket connector) RGB signal (G ON SYNC compatible) RGB . . . TTL level /positive and negative polarity /2. 2 k G ON SYNC . . . *Compatible with Microsoft's Plug & Play (VESA DDC1/2B) Output Mini D-sub 15 pin (socket connector) 75 /with buffer 34 En Additional Information English : Not available. Screen size (Dot x line) Remarks Vertical 56. 4Hz 70. 1Hz 60Hz 66. 7Hz 72. 8Hz 75Hz 85Hz 56Hz 60Hz 72Hz 75Hz 85Hz 74. 6Hz 60Hz 60Hz 70Hz 75Hz (74. 9Hz) 85Hz 60Hz 72Hz 75Hz 75. 1Hz 66. 0Hz 76. 0Hz 56Hz 60Hz 70Hz 60Hz 60Hz 75Hz 85Hz 60Hz 65Hz 70Hz 75Hz 85Hz Horizontal 24. 8kHz 31. 5kHz 31. 5kHz 35. 0kHz 37. 9kHz 37. 5kHz 43. 3kHz 35. 2kHz 37. 9kHz 48. 1kHz 46. 9kHz 53. 7kHz 49. 7kHz 31. 7kHz 852x480 1024x768 48. 4kHz 56. 5kHz 60. 0kHz (60. 2kHz) 68. 7kHz 53. 7kHz 64. 9kHz 67. 7kHz 68. 7kHz 61. 8kHz 71. 7kHz 45. 1kHz 48. 4kHz 56. 1kHz 60. 0kHz 64. 0kHz 80. 0kHz 91. 1kHz 75. 0kHz 81. 3kHz 87. 5kHz 93. 8kHz 106. 3kHz 960x768 ± ± 1024x768 ± ± ± ± 1280x768 ± ± 1280x768 ± ± ± ± 1280x768 (1600x1024) 1280x768 ± ± 1024x768 1280x1024 1280x768 984x768 ± 1280x768 ± 1024x768 ± ± ± 1024x768 ± ± 1016x768 1152x900 1280x768 ± ± ± 1280x768 ± ± Apple Macintosh 21" 1280x768 Sun Microsystems LO Sun Microsystems HI 1280x768 (1376x768) 640x480 ± ± ± ± 800x600 ± ± ± ± 832x624 852x480 1024x768 ± ± ± ± 1024x768 ± ± ± ± 1024x768 1280x768 ± 1280x768 ± ± ± ± 1280x768 ± ± ± ± 1280x768 DOT BY DOT 4:3 FULL PARTIAL NEC PC-9800 NEC PC-9800 (852x480) (864x480) Apple Macintosh 13" (1072x600) Apple Macintosh 16" ( ) indicates Apple Macintosh 19" Supplement 1 Resolution (Dot x Line) 640x400 -1/2: PDP-50P PC signal compatibilty table (INPUT1, INPUT2) Refresh rate 640x480 800 x600 832x624 1152x864 1152x870 1280x768 1280x960 1600 x 1200 : Optimal picture. [. . . ]