User manual PLANAR PE1700 Product Manual

[. . . ] PE1700 LCD Monitor USER'S GUIDE www. planar. com Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Unpacking the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Locations and Functions of Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The display will go into power saving. Caring for and Cleaning the Display To maximize screen life and prevent damage to the LCD panel, we recommend that you: Use the display power management system (if available on your PC). If you don't use a power management system, turn off the display when you won't be using it for an extended period. Don't press, rub, or poke the display with your finger or other object. Your LCD module is a high-quality optical device that requires special care when cleaning. Warning Don't use liquid, aerosol, or abrasive cleaning solutions to clean the screen. Gently dust the screen with a dry, soft, line-free cloth. Note: If the screen is still dirty, you can dampen the cloth with several drops of distilled water. Make sure the LCD panel is completely dry before you turn the display back on. OSD Display position of the OSD display for further adjustment. See Adjustment in the "OSD Display" Submenu" on page 21. Factory Recall Recall factory-setting values back. Languages Exit Open the "Languages" submenu where you can select one of the five languages for your preference in display OSD messages. See "Selecting Language for Your Preference" on page 23. Clear and exit the OSD main menu. Selecting Items in the OSD Menu To select items in the OSD "Main Menu", you will use the `Up ()' or `Down ()' buttons on the front panel of the display. To select items in the OSD submenus, you will use all three, control buttons. To select a specific submenu, you shall use `Up ()' or `Down ()' buttons to move forward or backward to the item to be adjusted, and then select it by press `Select' button. Adjusting the OSD Menu Auto Setup To perform the Auto Setup function you should follow the steps below: 1. Bring-up the OSD "Main Menu". - 10 - 2. The `Auto' icon should be highlighted already. 3. Use `Select' button to select and execute the Auto Setup function. After the execution of the Auto Setup function, it will show-up the follow message: If the image looks correct, choose Yes. OR If the image requires further adjustment, choose No, it will shown up `Phase' bar for your further adjustment by manual. Then you can adjust phase by `Up ()' or `Down ()' buttons. When all text appears well focused and there is no instability in the image, press the `Select' key to end up the adjustment. Adjusting the "Management" Submenu To perform the adjustment in the "Management" submenu you should follow the steps below: 1. Use `Up ()' (or `Down ()') to move forward (or backward) to the management icon and highlight it. - 11 - 3. Use `Select' key to enter the "Management" Submenu. [. . . ] Make sure that the computer's power is turn on. 2. Make sure that your graphic card has its output already. The message "Signal Out of Range" appears on my display. This message appears when the input signal is beyond the display's capability. Set your PC to a supported video mode, preferably 1280 x 1024 at 60 Hz. [. . . ]