User manual PLANAR PL190M Product Manual

[. . . ] PLANAR LCD MONITOR PL190M MANUAL www. planar. com Important Safety Instructions Read the Safety Instructions carefully and keep it for later use. Be aware of all warnings and instruction signs marked on the products. When cleaning, cut off the electrical supply at all times. Never use liquid or aerosol detergent, use a damp rag instead. [. . . ] The display unit contains high-voltage parts and may expose you to the electric shock. Contact your local dealer for the service if needed. When moving, always handle your LCD monitor with care. Do not forcefully press down the screen in case of damages to the monitor. Please refer to P. 5 to adjust the monitor. Cleaning the TFT LCD Monitor Wipe screen gently with a clean lens brush of camel hair, or a soft, clean, lint-free cloth. It can remove dust and other particles which will not scratch the LCD panel. If it is still not clean, blow and wipe gently with a soft, clean, lint-free cloth. Never pour or spray any liquid onto the LCD monitor. Do not apply pressure to the LCD panel. 4 Adjusting the Monitor Press down on the stand and gently adjust the monitor to a suitable viewing angle (see Figure below). Please note that this monitor can only be tilted forward to 5 degree and backward to 20 degrees. To prevent damage to the monitor, do not press the screen over its tolerant angles. Besides, this monitor can also be swiveled right and left to 45 degree. 5 O 20 O 45 O 45 O 5 Quick Installation Make sure the computer is turned off. Attach the female end of the power cord (Indication F) to the adapter (Indication E), then plug the adapter connector to the power "DC-IN (Indication A)" jack of the LCD monitor. When using a power cord, plug the male end into the wall socket. Plug one end of the 15-pin D-Sub signal cable (Indication G) in the "ANALOG" video signal connector (Indication B) of LCD monitor. If you use digital signal, plug one end of the 24-pin DVI-D signal cable in the "DIGITAL" video signal connector (Indication C) of LCD monitor. Note: This 24-pin Digital cable is optional. When using an audio cable, plug one end of the cable in the "AUDIO" jack of the LCD monitor (Indication D), and plug the other end in the jack of the sound card. Before your operations of the monitor, please refer to P. 7 "Operations" first. A B C D DC IN ANALOG AUDIO E I F G A. Audio Cable H 6 Operations Push the power button (Indication E) on the front of the LCD monitor to turn it on. When the power light (Indication F) turns green, the LCD is ready to use. Push the power switch button to turn off. A B C D F E Function Keys A. [. . . ] TCO99 and TCO95 50W (Typ), 60W (Max) (green LED) 3W (orange LED) 2W X 2 Storage Conditions Dimensions Weight Net Gross Safety EMI Low Radiation EMC Energy Star Quality Environment On Off Speakers Regulations Power saving Audio Specifications are subject to change without prior notice. 12 Factory Preset Timings Timing VGA 640 X 350 VGA 720 X 400 VGA 640 X 400 VESA 640 X 480 VESA 640 X 480 VESA 640 X 480 VESA 640 X 480 VESA 800 X 600 VESA 800 X 600 VESA 800 X 600 VESA 800 X 600 VESA 832 X 624 VESA 1024 X 768 VESA 1024 X 768 VESA 1024 X 768 VESA 1024 X 768 VESA 1024 X 768 VESA 1280 X 1024 VESA 1280 X 1024 Horizontal Frequency (KHz) 31. 470 31. 467 31. 469 31. 469 37. 861 37. 500 35. 000 35. 156 37. 879 48. 077 46. 875 49. 715 48. 363 56. 476 58. 036 60. 023 60. 241 63. 981 79. 976 Vertical Frequency (Hz) 70. 089 70. 082 70. 087 59. 940 72. 809 75. 000 66. 667 56. 250 60. 317 72. 188 75. 000 74. 535 60. 004 70. 069 71. 916 75. 029 74. 927 60. 020 75. 025 Sync Polarity (H/V) +/-/+ -/+ -/-/-/Composite +/+ +/+ +/+ +/+ Composite -/-/-/+/+ Composite +/+ +/+ Power Management System This monitor matches VESA DPMS (Display Power Management Standard) Standards. For the monitor's power saving features to work, the video board or computer must also match VESA DPMS standards. The Off state means the monitor is in the lowest DPMS state with the highest power savings. 13 Appendix FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ]