User manual PLANAR PL1911M Product Manual

[. . . ] PL1911M Planar Systems, Inc 1195 NW Compton Drive Beaverton, OR 97006-1992 www. planar. com Customer Service Planar provides the following technical support services: Internet Support For support available 24/7 visit Planar's Online Technical Support at www. planar. com/support. Our Online Technical Support is where you'll find solutions to many common problems, download documentation, view answers to frequently asked questions (FAQs) and get troubleshooting advice, or email Planar your support question. Talk to a Customer Service Representative To contact Planar's Customer First(TM) Technical Support Service call 1. 866. PLANAR. 1 (866. 752. 6271). This service is available 5am - 5pm Pacific Time, 8am - 8pm Eastern Time, Monday through Friday. [. . . ] A certified line is required to connect this device to a power outlet. For a nominal current up to 6A and a device weight above 3 kg, a line not lighter than H05VV-F, 3G, 0. 75 mm2 must be used. Important Recycle Instruction: LCD Lamp(s) inside this product contain mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws. For more information, contact the Electronic Industries Alliance at WWW. EIAE. ORG. For lamp specific disposal information check WWW. LAMPRECYCLE. ORG. 3 Chapter 1 Installation Unpacking Before unpacking the LCD Monitor, prepare a suitable workspace for your Monitor and computer. You need a stable and clean surface near a wall power outlet. Make sure that LCD Monitor has enough space around it for sufficient airflow. Though the LCD Monitor uses very little power, some ventilation is needed to ensure that the Monitor does not become too hot. After you unpack the LCD Monitor, make sure that the following items were included in the box: * LCD Monitor * Monitor-to-PC VGA Cable * Monitor-to-PC DVI-D Cable * User's Manual * Power Cord * Stereo Jack Audio Cable Register Your Planar Products Today Thank you for choosing Planar. To assure you receive all the benefits of your Planar product and services, register your Planar product today. Visit our website to register your product at http://www. planar. com/support/product_registration. html Cables, Replacement Lamps and Accessories To find cables, replacement lamps and accessories for your Planar projector, LCD monitor, touchscreen or other Planar products visit our online store at www. PlanarOnline. com or find other stores who carry Planar products at http://www. planar. com/howtobuy 4 Height Adjustment Stand To unlock the height adjustment feature of the stand, locate the pin on the back of the stand column and turn the pin knob counter-clockwise. (See fig. 1-1 ) Figure 1-1 Tilt, Swivel and Pivot Rotation The LCD Monitor is designed to have a tilt range of -5°to +25°, a swivel range of -35°to +35°, and a 90° pivot rotation. 1-2) Figure 1-2 Warning: Do not force the LCD Monitor over its maximum viewing angle settings as stated above. Attempting this will result in damaging the Monitor and Monitor stand. The monitor stand base may forcefully extend and cause injury. Raise the monitor to its "Full Up" position before removing the monitor stand. Optional Mounting Alternatives Warning: The monitor stand base may forcefully extend and cause injury. position before removing the monitor stand. Raise the monitor to its "Full Up" Optional Mounting Alternatives Warning: The monitor stand base may forcefully extend and cause injury. Raise the monitor to its "Full Up" position before removing the monitor stand. Detaching LCD Monitor from Its Stand Unscrew screws the swivel base support column and pull down the second. Figure 1-3 Interface for Arm Applications Before installing to mounting device, please refer to Fig. 1-3. The rear of this LCD display has four integrated 4 mm, 0. 7 pitches threaded nuts, as well as four 5 mm access holes in the plastic covering as illustrated in Figure 1-4. These specifications meet the VESA Flat Panel Monitor Physical Mounting Interface Standard (paragraphs 2. 1 and 2. 1. 3, version 1, dated 13 November 1997). [. . . ] Attention: After Auto Adjustment, the display might display wrong position or size, if it has received a pattern which has no screen border. You may select either Analog or Digital Input video when VGA input or/and DVI Input is/are available. Saves the values of this setting and exits the OSD menu function. Auto and Input Select Exit Icon 9300 7500 6500 User Function CIE coordinated Color Temperature of 9300°K CIE coordinated Color Temperature of 7500°K CIE coordinated Color Temperature of 6500°K Three colors (Red, Green, Blue) can be adjusted from the OSD menu Description Sets the CIE coordinate color temperature to 9300°K Sets the CIE coordinate color temperature to 7500°K Sets the CIE coordinate color temperature to 6500°K Sets the settings to a by user defined CIE Temperature. 8 Notice: "OSD Lock Out" Function: When monitor is in normal display, you can enable the "OSD Lock Out" function. * How to enter "OSD Lock Out" function => Step 1: The monitor is displaying after power on. Step 2: To press the buttons "VOL ­" and "VOL+" and "Function >" at the same time for 3 seconds or more. Step 3: Monitor will show an "OSD Lock Out" message for 5~10 seconds and the message will disappear automatically. While the monitor is in the state of "OSD Lock Out", if press OSD button, "OSD Lock Out" message will appear for 5~10 seconds on screen. * How to exit "OSD Lock Out" function => Step 1: When the monitor is in the state of "OSD Lock Out" . Step 2: To press the buttons "VOL ­" and "VOL+" and "Function >" at the same time for 3 seconds or more. Step 3: Display will show main OSD menu. [. . . ]