User manual PLANAR PL2010 Product Manual

[. . . ] PL2010 1 The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright. No part of this document may be reproduced, translated to another language or stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission. Windows is a registered trademark of Microsoft Inc. [. . . ] Save the original shipping carton and packing materials, as they will come in handy if you ever have to ship your monitor. For maximum protection, repackage your monitor as it was originally packed at the factory. To keep the monitor looking new, periodically clean the case & surface of the TFT-LCD panel with a soft non-fiberous cloth lightly dampened with a glass cleaner. Do not use any paper products to clean the screen. Never spay the glass cleaner directly on the monitor. Never use strong solvents such as thinner, benzene, or abrasive cleaners, since these will damage the case & panel. As a safety precaution, always unplug the monitor before cleaning it. · · · · 7 GENERAL NOTES (cont. ) · · Plug & Play DDC1/2B Feature - This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The communication channel is defined in two levels, DDC1 and DDC2B. The DDC1 is a unidirectional data channel from the display to the host that continuously transmits EDID information. The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC2B channel. This monitor will appear to be non-functional if there is not video input signal. In order for this monitor to operate properly, there must be a video input signal. 8 BEFORE YOU OPERATE THE MONITOR FEATURES · 20" (51cm) TFT Color LCD Monitor · Crisp & Clear Display for Windows · Recommended Resolution: 1600 X 1200 @ 60Hz · Ergonomic Design with Tilt Adjustable Stand · Space Saving, Compact Case Design CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following items: Monitor Base Landing Strip User Manual Power Cord 15-pin D-Sub Cable 24-Pin DVI Cable Planar Product Family CD 9 INSTALLATION INSTRUCTIONS Power Source: 1. Make sure that the power cord is the correct type required in your area. This LCD monitor has an internal Universal Power Supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required. ) 3. Connect the AC-power cord into your LCD monitor's AC-power-input. The AC-power cord may be connected to either a wall power outlet or the power outlet socket on your PC, depending on the type of power cord supplied with your LCD monitor. A certified power supply cord has to be used with this equipment. The relevant national installation and/or equipment regulations shall be considered. A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 0. 75mm2 or H05VVH2-F2 3G 0. 75mm2) shall be used. As an alternate, a flexible cord of synthetic rubber according to IEC 60245 (designation H05RR-F 3G 0. 75mm2) shall be used. [. . . ] Do not execute reset, return to main menu. Position OSD Timeout English Langua ge Deutsch Français Español Italiano Select the language you like Information Informat ion Yes Reset No N/A Exit N/A N/A N/A N/A N/A N/A N/A N/A 19 TECHNICAL SUPPORT (FAQ) Problem & Question Power LED is not on Possible Solution *Check if the Power Switch is in the ON position *Power Cord should be connected *Check if the PC system is Plug & Play compatible *Check if the Video Card is Plug & Play compatible *Check if the D-15 plug pin of Video Cable is bent *Adjust the Contrast and Brightness Controls. *Move electrical devices that may cause electrical interference. *Computer Power Switch should be in the ON position. [. . . ]