User manual PLANAR PT150M-MU Product Manual

[. . . ] Warning Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Compatibility Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 18 19 20 2 Usage Notice Warning- To prevent the risk of fire or shock hazards, do not expose this product to rain or moisture. [. . . ] Slots 75mm VESA Mounting Interface 75mm Note!The depth from plastic back cover to the bottom of the screw hole is 8mm. The spec is M4 screw. Start Your Installation Remove the Back Cover Please follow these instructions to remove the cover on the back panel of the LCD so that you can connect the cables in "Connector Ports B. " 9 A Back Cover 1. To remove the back cover, follow the arrows in Figure A and press with both your thumbs. The cover should be removed by pressing firmly. Follow the instruction on P. 11 (Figure 11. 1) to connect the cables in "Connector Ports B. " 3. You may also keep the cables in order with the included cable organizer. Included Cable Organizer Note: You can place the LCD flat horizontally to make it easier to connect the cables. Please make sure that you place it on an even surface lest the LCD should be damaged by scratches or collision. 10 Connecting the Display (Figure 11. 1) To setup this display, please refer to the following figure and procedures. Be sure the computer and monitor are turned off. Connect the DC power cord to the power connector; plug one end of the AC power cord into the power adapter, and then the other end into an electrical outlet( ). Connect the VGA signal cable from display VGA input connector to the 15-pin connector of your host computer and tighten the screws( ). Connect the Audio-In cable from audio input port of your display to the Audio-out port of your computer( ). Connect the RS-232 cable from RS-232 port of your display to the RS-232 port of your computer( ). Turn on your computer, display and video source. Notice: To ensure the LCD display can work well with your computer, please configure the display mode of your graphic card to make it less than or equal to 1024 x 768 resolution and make sure timing of the display mode is compatible with the LCD display. We have listed the "Compatibility Modes" of this LCD display in appendices for your reference. 11 Figure 11. 1 Audio-In Cable VGA Cable RS232 Cable Power Adapter & Power Cord 12 User Controls Front Panel Controls AUTO MENU SELECT No. / Icon MENU SELECT/AUTO Control Menu button Select/Auto Function Display the OSD menus Select- To select the adjustment items from OSD menus. Auto- To activate the "Auto Adjustment" function to obtain an optimum image. 1. Decreases the brightness of the display image. 2. Decreases value of the adjustment items. 1. Increases the brightness of the display image. 2. Increases value of the adjustment items. Switches on/off the power of the LCD display. 1. Green indicates the display is turned on. [. . . ] 4 Check and reconfigure the display mode of the vertical refresh rate of your graphic card to make it compatible with the LCD display. Problem: Vague image (characters and graphics) 4 Use " Frequency " to make an adjustment. If this problem still exists, use "Tracking" to make an adjustment. 19 Warning Signal If you see warning messages on your LCD screen, this means that the LCD display cannot receive a clean signal from the computer graphics card. There may be three sources for this problem. Please check the cable connections or contact Planar for more information. 4 No Signal This message means that the LCD display has been powered on but it cannot receive any signal from the computer graphic card. [. . . ]