User manual PLANAR PX212M Product Manual

[. . . ] 3 Package Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Start Your Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 User Controls Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] - Place in direct sunlight. 3 Introduction About the Product Having a 21. 3 LCD dsiplay with an active matrix, thin-film transistor (TFT) liquid crystal display (LCD), this product also demonstrate the following outstanding features. q q q q q q q q q q q q q Dual Analog and Digital signal input 21. 3" diagonal screen size 1600 x 1200 high resolution Wide Viewing Angle Technology 31. 5 ~ 91. 1 kHz horizontal scan 56 ~ 85 Hz refresh rate Auto Adjustment and Re-scaling function High quality full screen re-scaling capability Multilingual OSD user controls VESA DPMS power saving Video capability Audio capability Kensington lock capability 4 Package Overview LCD Display Power Adapter Power Cord VGA Signal Cable DVI-D Cable Audio-In Cable S-Video Cable Video Cable User's Guide Landing Strip Family Product CD CD-ROM for Pivot software 5 Installation Product Overview u Front View Liquid Crystal Display (LCD Display) Panel Controls Stand u Back View Kensington Security Lock Slot Connector Ports (Inside the back cover) V ID E O S - V ID E O DVI Input Port DC-In Analog Input Port Audio Composite Video S-Video 6 u Tilt Grasp the LCD Display with both hands and adjust the tilt as desired. Tilt Angle:-5° ~ 35° u Kensington Security Slot The monitor can be secured to your desk or any other fixed object with Kensington lock security products. Kensington lock is not included. Kensington Security Slot 7 u VESA Mount on your monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface Standard which defines a physical mounting interface for flat panel monitors, and corresponding standards for flat panel monitor mounting devices, such as wall and table arms. The VESA mounting interface is located on the back of your monitor. The VESA Mounting slots of this model are located inside the rear cover (shown in the following figure). To mount the monitor on a swing arm or other mounting fixture, follow the instruction included with the mounting fixture to be used. Slots 100mm 100mm VESA Mounting Interface Warning!The depth from plastic back cover to the bottom of the screw hole is 8mm. The spec is M4 screw. 8 Start Your Installation u Connecting the Display (Figure 10. 1) To setup this display, please refer to the following figure and procedures. Connect the DC power cord to the power connector; plug one end of the AC power cord into the power adapter, and the other end into an electrical outlet(). For the PC with Analog output: Connect the VGA signal cable from display VGA input connector to the 15-pin connector of your host computer and tighten the screws(). For the PC with DVI digital output: Connect the DVI signal cable to the connector of the display card in your computer; connect the other side to the DVI-D input port of your display. If your video source uses a round, four-prong S-Video connector, please use the S-Video cable(). If your video source uses a round, one-prong composite video connector, please use the video cable(). If your audio source uses a round, one-prong composite audio connector, please use the audio cable(). Turn on your computer, display and video source. Notice:To ensure the LCD Display will work well with your computer, please configure the display mode of your graphics card to make it less than or equal to 1600 x 1200 resolution and make sure the timing of the display mode is compatible with the LCD screen. We have listed the "Compatibility Modes" of this LCD screen in appendices for your reference. 9 Figure 10. 1 Video Cable Audio Cable S-Video Cable V ID E O S -V ID E O Power Adapter & Power Cord DVI-D Cable VGA Cable 10 User Controls Front Panel Controls 11 No / Icon Control Menu button Function MENU To pop the OSD menus. To select the adjustment items from OSD menus. To activate the "Auto adjustment" function to obtain an optimum image. Decreases the brightness of the display image. Decreases the value of the adjustment items. Increases the brightness of the display image. Increases the value of the adjustment items. Green indicates the display is turned on. Amber indicates the display is in power-save mode. Switches On/Off the power to the LCD Display. S E LE C T Select/Auto 3 Brightness Minus/Minus 4 Brightness Plus/Plus Power LED Power Switch 12 How to Use the OSD Menus 1. [. . . ] If the problem persists, please contact your local dealer or our service center. Problem: No image appears on screen. 4 Check that all the I/O and power connectors are correctly and well connected as described in the "Installation" section. 4 Make sure the pins of the connectors are not crooked or broken. Problem: Partial image or incorrectly displayed image. 4 Check to see if the resolution of your computer is higher than that of the LCD Display. 4 Reconfigure the resolution of your computer to make it less than or equal to 1600 x 1200. Problem: Image has vertical flickering line bars. 4 Use "Frequency" to make an adjustment. [. . . ]