User manual PLANET BIKE PROTEGE 8.0

[. . . ] Use any combination of rubber shims to fit different diameter handlebars. Tighten the screw so the bracket will not rotate on the handlebars. Slide the computer head into the bracket until it MOUNTING BRACKET "snaps" into place. L L STEP 5: TEST. Install computer head into bracket and rotate front wheel to test for proper function of magnet/wheel sensor alignment. [. . . ] Upon release, the M/H or K/H icon will flash. L L 1) Miles or Kilometers Selection: Once "M/H" or "K/H" is flashing, press "mode" to switch to desired selection. Press "set" to lock in your selection and advance the screen to Wheel Size Setting. L L 2) Wheel Size Setting (WSS): The screen will now display default WSS "2154" with the "4" flashing. L * Background information: The bicycle computer calculates information based upon the distance traveled each time your wheel goes around. The wheel L size setting equals the distance in mm traveled in one revolution of your wheel. There are two methods to determine the wheel size setting. L * For WSS less than 1000mm, input your WSS in WSS . WSS does not allow a size less than 1000mm. L Method 1: Read the tire size on the side wall of your tire and input the number that corresponds to your tire size on the wheel size chart to the right. Since there are many tire manufacturers and designs, tires listed as the same size from different manufacturers can actually vary significantly in their actual circumference. Therefore, we recommend for maximum accuracy in you computer readings, to use Method 2. L Method 2: Wheel Roll Out: For best results, find a flat smooth surface to perform the wheel roll out and inflate your tires to riding pressure. L 1) Place a piece of masking tape or draw a line on the surface to determine a starting position. L 2) Position the front tire valve at the 6:00 position (diagram #7) directly above the staring position. L 3) Roll the bicycle forward one revolution of the wheel on a straight line until the valve stem is again at the 6:00 position. (Note: Putting pressure on the handle bars to simulate body weight on the tire will give more accurate results. ) Mark the finishing position with masking tape or a line. Repeat the procedure if necessary and average the results. Measure the distance between the starting and finishing positions in mm, this is your WSS. (Note: If you use an inch measuring tape, multiply inches by 25. 4 to achieve mm. ) This is your WSS in mm. L SET PRESS HERE TOL SWITCH BETWEENL AND MODE 6 TIRE SIZE 20 x 1. 75 24 x 1. 0 24 x 1. 75 24 x 2. 0 26 x 1. 25 26 x 1. 5 26 x 1. 95 26 x 2. 0 26 x 2. 1 26 x 1 (559 mm) 26 x 1 (650 c) BATTERYL REMOVAL WSSL 1502L 1750L 1894L 1925L 1950L 1996L 2055L 2066L 2070L 1925L 1925 TIRE SIZE WSSL 700 x 18C 2072L 700 x 20C 2091L 700 x 23C 2105L 700 x 28C 2143L 700 x 32C 2160L 700 x 38C 2184 FOR FUTURE REFERENCE, L WRITE YOUR WSS HERE: Imputing Wheel Size Setting (WSS)L A) Press "mode" button to change "flashing" first digit to desired selection. L B) Press "set" button to lock in your selection and advance to the next flashing digit. L C) Repeat steps A-B until all four digits are set. After the forth digit is set, it will L advance the screen to Odometer setting. 3) Odometer Setting STARTINGL POSITION FINISHINGL POSITION 7 ONE REVOLUTION = WHEEL SIZE SETTING (mm) : The digit on the far right will be flashing. (If you don't need to set the Odometer, repeatedly press "set" to advance to WSS . ) Repeat steps A-B again to set the Odometer. L L 4) Wheel Size Setting (WSS): The screen will now display default WSS "0000" with the first "0" flashing. Repeat steps to set WSS . L L 5) Odometer Setting : Repeat steps to set Odometer . L L 6) Clock Setting: The hour digit on the far left will be flashing. To reset the clock only, press mode button until clock function is displayed on line four. Press "set" button to initiate clock reset. When you are done, the computer will enter normal operating mode. Replace the computer in its bracket and you are ready to ride!To reset ride settings other than the clock, press the mode button until until the forth line displays any function except "CLOCK" or "BIKE ODO. " Press and hold the set button for 3-4 seconds. release, the computer will enter "reset" mode. [. . . ] Make sure the rubber water seal gasket is in place and the battery cover is flush with battery case. Refer to Computer Setup and Programming to re-input setup data. 7. Trouble Shooting 1) Display is blank or shows partial digitsL Remove and reinsert battery. If problem persists, a new battery may be required. L L 2) LCD displays numbers but does not record data when riding. L Check for proper wheel sensor/magnet alignment (See Section #2, Step #2). [. . . ]