User manual PLANTRONICS CS60

[. . . ] The Talk Indicator (15) on the base unit will illuminate and the On-Line Indicator (23) on the headset will flash when in Headset mode. Both of the indicators are extinguished when in Handset mode. PLACING A CALL USING YOUR HEADSET To place a call using the headset, the system must be in Headset mode. Take the handset off the hook and dial in the normal way. You will then be able to talk through your headset. [. . . ] The handset lifter then lowers the handset to end the call. RECEIVING A CALL USING THE LIFTER When a new call is received the telephone rings as normal, but in addition, a ring alert comprising a repeating sequence of three short beeps will be heard in your headset. Note: This additional call alert is only active when the Lifter (17) is connected. To answer the call press the Talk Button (20) on the headset. The lifter will then raise the telephone handset off the hook and you will then be able to talk to the caller. When you have finished your call press the Talk Button (20) on your headset. The handset lifter then lowers the handset to end the call. IntelliStandTM FUNCTION When the CS60 DECTTM Wireless Headset System is used in conjunction with a Plantronics Handset Lifter (17), you can enable the IntelliStand feature. The IntelliStand senses when the headset has been removed or replaced in the CS60 Base Unit, automatically activating the lifter to answer or end a call. The IntelliStand feature is disabled when the IntelliStand switch (5) is in position I or enabled when the switch is in position II. SWITCHING FROM HEADSET TO HANDSET WHEN USING THE LIFTER If during a call you are using your headset and want to switch to the telephone handset, remove the handset from the Lifter, then press the Talk Button (20) on your headset. The Lifter will lower and you will then be able to continue the call using the handset. SWITCHING FROM HANDSET TO HEADSET WHEN USING THE LIFTER If during a call you are using the telephone handset and want to switch to your headset, press the Talk Button (20) on the headset. The Lifter will raise and you will be able to continue the call using your headset. Replace the telephone handset on the Lifter. When the call is finished press the Talk Button (20) on your headset. The Lifter will lower the handset and end the call. 7 UK TROUBLESHOOTING PROBLEM I plugged everything in but the lights won't come on. Possible Cause No power Solution Check that the AC Power Adapter is connected to the base unit. Check that the AC Power Adapter is connected to the mains supply. Check that the AC Power Adapter is the model supplied by Plantronics. PROBLEM I cannot hear caller / dial tone. Possible Cause CS60 DECTTM Wireless Headset System is not connected correctly Solution Check that the telephone is connected to the base unit's Telephone Cable Port. Check that the handset is connected to the base unit's Handset Cable Port. Ensure you are in headset mode Out of Range Headset battery is flat Listen volume too low Press the Talk Button to select correct mode. Recharge the battery by placing the headset in the Headset Docking Cradle. Adjust the Listen Volume Control on the headset. If the volume is still too low, select another Rx Slide Switch setting (refer to the Quickstart Guide). [. . . ] Kaikki yksiköt huolletaan täysin tuotantovaatimusten mukaan. Varaosina käytetään vain alkuperäisiä osia. · · Les produits sous garantie sont remplacés gratuitement. Les réparations répondent aux normes de production et sont réalisées avec des pièces d'origine. +358 9 88 16 85 20 S · · 0825 0825 99 0 , 15 TTC / mn Produkter med gällande garanti byts ut utan kostnad. Alla enheter uppfyller produktionsstandarden och består av originaldelar. I · · I prodotti in garanzia verranno sostituiti gratuitamente. [. . . ]