User manual PLUS U2-X2000

[. . . ] DATA PROJECTOR U2-X2000 User's Manual + S E R E W O P E C R U O S R E W O S P U T A T S O T U A U N E M - ENTER LE C T D R A C SS CE PC C A ST FO LD ER LI L. O V S LID E LIS T LR EA C -C NC AP E /C R K TE LID S LIC IN -C PO Y D M AG N R na lo g ) O T U A O E ID -V S I V D (A J P IMPORTANT * DLPTM (Digital Light Processing) and DMDTM (Digital Micromirror Device) are registered trademarks of Texas Instruments Incorporated (U. S. A. ). * DMDTM is an ultra-precise part developed by Texas Instruments (U. S. A. ) which takes the place of liquid crystal (in the projector). * AccuBlend is a trademark of NEC Viewtechnology, Ltd. [. . . ] When the source is set to RGB, if "Auto Adjust (RGB only)" is set, "Video Filter" is displayed in white characters and cannot be selected. See "Auto Adjust (RGB only)" on page E-53. Use the SELECT buttons to select the setting. On . . . . . . . . . . . . . . . The filter is turned off. E-43 Image Options Factory Default Use this to set all the adjustments and settings stored in the projector or the adjustments for the currently displayed source only back to the default values. Use the SELECT The buttons to select the desired mode. icon is displayed while the values are being reset. All Data . . . . . . . Select this to set all the adjustment and setting values adjusted or set for all the sources back to their factory default values. Data reset All adjustment and setting values other than "Language", "Communication Speed", "Remaining Lamp Time", "Lamp Hour Meter" and "Projector Usage" (To reset the "Clear Lamp Hour Meter" setting, see page E-55. ) Current Signal . . . . . . . . . . . . . . . . . . . Select this to set the adjustment and setting values for the currently displayed source only back to the factory default values. Data reset "Brightness", "Contrast", "Color", "Hue", "Sharpness", "Gamma Correction", "Aspect Ratio", "Noise Reduction", "Color Matrix", "White Balance", "Horizontal", "Vertical", "Clock", "Phase", "Resolution" and "Video Filter". E-44 Color Management Gamma Correction Select the gradation of the black parts of the image. This makes even the darker parts of the picture look clearer. Select the gamma correction mode using the SELECT Normal . . . . . . . This setting is suited for watching TV programs and general image sources. This setting is suited for watching movies. buttons. Color Matrix Use the SELECT buttons to select the item, then use the buttons to select the setting. SELECT Select Color Matrix Set the color matrix for high definition TV programs or digital programs. Select the input signal color matrix type. High definition broadcast color matrix SDTV . . . . . . . . . . Digital broadcast color matrix Select Color Matrix Type Select the format for separating video composite signals into RGB signals. Pb/Pr matrix type White Balance This adjusts the signal's while and black levels to optimize color reproduction. Use the SELECT buttons to select the item, then use the SELECT adjust. buttons to Use "Brightness R", "Brightness G" and "Brightness B" to adjust the black of the picture. Use "Contrast R", "Contrast G" and "Contrast B" to adjust the white of the picture. E-45 Projector Options [Menu] Menu Mode Select the menu to be displayed. [. . . ] Order this from your PLUS dealer using the unit model number. E-75 Replacing the Lamp Cartridge Preparations: Turning the projector upside-down on top of a soft cloth, etc. , so that it does not get scratched makes it easier to replace the lamp cartridge. Turn the projector right-side up after replacing the lamp cartridge. 1 Unplug the power cord. 3 Remove the lamp cover. (1) Turn the lamp cover's set screw counterclockwise and loosen until the screw turns freely. (The screw does not come off. ) (2) Open the lamp cover a little, then pull it in the direction of the arrow and remove it. 4 Remove the lamp cartridge. (1) Turn the lamp cartridge's two set screws counterclockwise and loosen them until the screws turn freely. [. . . ]