User manual PLUS V-1080

[. . . ] DATA PROJECTOR V-1080/V-807 User's Manual Q ME UIC NU K EL NC CA N ST HK Z OO M VO L MEN U IMPORTANT Digital Light Processing, DLP, Digital Micromirror Device and DMD are all trademarks of Texas Instruments. Windows 98, Windows 95, and Windows 3. 1 are registered trademarks in the United States and other countries of Microsoft Corporation. IBM is a registered trademark of International Business Machines Corporation. Macintosh and MAC are trademarks of Apple Computer Inc. [. . . ] In Screen Example 3, horizontal and vertical keystone distortion should be adjusted. (3) To close the display immediately, press the CANCEL button. In the absence of operations for a period of about 10 seconds, the display will close automatically. Screen Example 3 Note * The keystone adjustment values can be overwritten and saved. * Overcompensation of the horizontal keystone correction value will result in a narrowing of the vertical keystone adjustment range. Likewise, overcompensation of the vertical keystone correction value results in a narrowed horizontal adjustment range. * Note that the adjustment range will differ depending on the adjustment conditions. * The screen examples have been depicted in an exaggerated form to aid in description. E-34 General Operation Enlargement of the Image and Video Movement This function digitally enlarges the personal computer image and video image (up to 10 times). The zoom selection display will appear. U MEN Zoom (3) (4) CAN CEL 21 ­ + ENTER (2) Enlarge to the desired size. Each press of the (+) button enlarges the image and each press of the (-) button makes the image smaller (returning it to 1:1). (3) Pressing the cursor ( ) buttons at the time of the zoom operation will cause the display position to move. (There will not be any movement when zoom is at 0. ) (4) To close the display immediately, press the CANCEL button. In the absence of operations for a period of about 10 seconds, the display will close automatically. (1) (2) (3) HKS TN VKST N ZOOM VOL (2) (1) (No enlargement) (Approximately 2 times enlargement) (Movement) The image can also be moved in the following circumstances. * * When "Aspect" is set to "Real" by the signal of the personal computer, and the input resolution is higher than the display resolution of the projector. When "Aspect" is set to "Zoom" by the video signal. Note * Zoom and image movement functions are cancelled when the input is switched. * The greater the zoom enlargement, the less distinct the image will appear. The reason for this is that the dots are being digitally corrected so that they are not conspicuous. * Movement of the screen will not be possible when the menu screen is being displayed. E-35 General Operation Adjustment of the Volume This function adjusts the volume of the built-in speaker. The volume adjustment display will appear. Volume (3) MEN U CAN CEL 53 ­ + ENTER (2) Adjust the volume. The (+) button increases the volume and the (-) button decreases the volume. (3) To close the display immediately, press the CANCEL button. In the absence of operations for a period of about 10 seconds, the display will close automatically. HKS TN VKST N ZOOM VOL (2) (1) E-36 Menu Operation Method This section describes only the menu operation method. Please see this page should you need information while performing menu operations. [. . . ] Order this from your PLUS dealer using the unit model number (see "Note" below). Note · When the lamp usage time reaches 1100 hours, it becomes impossible to switch on the power and menus are not displayed. In such a case, see "If the unit doesn't go on because lamp usage exceeds 1100 hours" on page 25. · Obtain a replacement lamp cartridge at the store where the unit was purchased. Please specify the following information when ordering a replacement lamp cartridge: Model name : V-120 Product code : 28-060 E-66 Replacing the Lamp Cartridge PREPARATION Turn the projector upside down and place it on a soft cloth that has been prepared in advance to prevent scratches. [. . . ]