User manual POLAROID ID100

[. . . ] 4 Press the MIN and SEC buttons simultaneously, to clear the numbers. RUN HEAT OFF Replacement battery: The timer uses one #LR44 or equivalent battery. They can be purchased wherever watch, calculator, or hearing aid batteries are sold. 2 Install the Validation Plate The validation plate determines the location of the portrait on the ID card. The validation plate may include a validating signature or seal for additional security. Contact your Polaroid dealer or representative for details and ordering information. Load the Film The ID-100 Systems use Polaroid instant color films, such as: · · · · · Polacolor 100 ID UV film Polacolor ID Ultraviolet (U. S. A. [. . . ] The camera does not operate until each step is completed. Make sure the card selector switch is in the correct position for the picture you need to take (duplicate or single). 3 Press the timer START button. 1 Take the data card from the subject. 2 Orient the card so that you can read it, and then slide it all the way into the slot. Note: In some camera models, the slot is on the right hand side of the camera. The slot is on the top of the camera for the vertical model. With the Pro model, the data card holder is removable for easy cleaning. 3 Grip the sides of the camera, and tilt it as needed to place the aiming light on the subject's chin. The aiming light stays on for 10-15 seconds. 4 4 Place the sheet of film near the timer. At the end of the processing time, the timer beeps. Laminate the Pictures Most ID cards are sealed or laminated inside a plastic pouch for protection. Plastic pouches are designed for use with wet, newly separated pictures, or with dry pictures. The following list provides guidelines for the type of pouch you use for your ID pictures (wet or dry pictures): 5 Separate the print from the negative, starting at the end nearest the arrows. en Ev erg re I M. BO OT Pouch Types · Co lle ge H Front and back are transparent Use with wet or dry pictures. Insert a wet picture into the pouch with the picture facing the side imprinted with the word Polaroid. Insert a dry picture facing the non-printed side. · Polaroid-printed transparent front and opaque back Ev erg re en Co lle M. ge BO OT m e Na m e LE gn at ur e NE ud en 03 t No 8 0 , 4 Si SO PH IL . EN St E Si gn at ur e Cl as s Cl as s SO PH . St ud en 03 t No 80 , 4 Na H 6 Fold the negative, moist side in and dispose of it properly. See the film packaging for recommended film handling and cautions. Wet pictures only. · Non-printed transparent front and opaque back Dry pictures only. Note: If the edges of the ID card are ragged, the laminator ther- Cut the Print 1 Insert the print into the die cutter as shown. Class Class mostat may be set too high. If the pouch is not completely sealed, the laminator thermostat may be set too low. See the section Adjust the Laminator Thermostat. 1 Move the laminator switch to the right to turn on the rollers. Evergreen College Name SOPH. SOPH. 03480 Student No, Student No, 03480 Signature Evergreen College Name Signature ILENE M. BOOTH 2 Place the picture inside the pouch. Colle ge Eve rgre en Name 2 Ensure that the pictures are centered left to right. ILEN 0348 0 Sig natur e E M. H Studen t No , Signat ure 3 Push down on the handle to cut the picture into two ID cards. Class 3 Place the pouch inside the carEvergreen College Name 4 Release the handle, and then remove the excess paper from the die cutter. 5 Cla ss SOPH . Stud 0348 ent 0 No , Na me Eve rgre en Co ILEN lleg E M. e rier with the sealed side of the pouch against the closed side of the carrier. BOOT Class SOPH . SOPH. Class BOOT H SOPH. Stude Student No, 03480 80 034No, Name Signa ture nt Signature ge Colle reen Everg BOOTH ILENE M. BOOTH ILENE M. Class SOPH. Class SOPH. Stud Student No, 03480 80 034No, Nam Sign ature ent Signature Evergreen College Name llege een Co Evergr BOOTH ILENE M. [. . . ] Otherwise, the warranty period is determined by the date of manufacture. This warranty does not apply to damage caused by accident, misuse or tampering, and excludes all consequential damages except in jurisdictions not allowing such exclusions or limitations. Radio and television interference EMI Notice (Canada) This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. LE PRESENT APPAREIL NUMERIQUE N'EMET PAS DE BRUITS RADIOELECTRIQUES DEPASSANT LES LIMITES APPLICABLES AUX APPAREILS NUMERIQUES DE CLASS B PRESCRITES DANS LE REGLEMENT SUR LE BROUILLAGE RADIOELECTRIQUE EDICTE PAR LE MINISTERE DES COMMUNICATIONS DU CANADA. EMC Notice (Germany) Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Notice (U. S. A. ) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ]