User manual POLAROID SPRINTSCAN 45 ULTRA QUICKSTART GUIDE

[. . . ] Adapter for single 35mm slide Adapter for 120 film, 2 1/4 x 2 3/4 in. Four-slide film carrier 35mm slide spacer (not shown) Two magnets for 120 film (not shown) The PolaColor Insight Software CD (not shown) containing: · PolaColor Insight software for Windows 95, 98, and NT · PolaColor Insight software for Power MAC and PowerPC systems and an Adobe Photoshop plug-in · Online user's guide Do not disassemble the scanner. Doing so could result in severe electrical shock and damage to the scanner. This action may also void your warranty. [. . . ] Position the film so the image is right-reading and right-side up (emulsionside down). Note: The emulsion side is the dull side. The 120 Film Adapters (for 2 1/4 x 21/4 and 2 1/4 x 2 3/4 in. film) 1 2 Open the 4x5 carrier as described previously. Locate the appropriate adapter for your image. square images. Note: The frame of film must be cut from the film strip in order to be scanned. 3 Pins 3 Orient the adapter so that the words THIS SIDE UP (on the adapter) face up, and the notches are at the left edge. Place the unmounted film over the opening, within the raised ridges of the adapter. Position the film so the image is rightreading and right-side up. 3 Close the carrier. Squeeze the carrier at the bottom edge and turn the knob to lock it. 4 Secure the film with the two magnets provided, on the top and bottom edges. Be sure the magnets are also within the raised ridges. The Single-35mm Carrier 1 5 Open the 4x5 carrier as described previously. Locate the single-35mm adapter. Note: You can use a negative, or a mounted or unmounted Place the adapter in the 4x5 carrier, sliding the notches into the pins on the left edge. The film and magnets should be face up, as shown. 2 slide. 3 Orient the adapter so the metal tabs face up, and the notches are at the left edge. Slide the film into the channel, under the two metal tabs. Position the film so the image is rightreading and right-side up. 6 Close the carrier. Squeeze the carrier at the bottom edge and turn the knob to lock it. English 12 English 13 4 If the film is unmounted or the mount is thin, use the slide spacer provided. Position the slide spacer on top of the slide. The film should fit snugly into the adapter. (The spacer also ensures that the image will be at the correct distance from the scanning mechanism. ) 6 Close the carrier. Squeeze the carrier at the bottom edge and turn the knob to lock it. XT TE 5 Place the adapter in the 4x5 carrier, sliding the notches into the pins on the left edge. The slide and tabs should be facing up. 7 Insert the Carrier into the Scanner 1 3 Close the carrier access door. The scanner will not scan if the door is open. Note: Do not open the carrier access door while a scan is in Open the carrier access door. process; the scan will be interrupted. The scan will resume when the door is closed, but the quality of the scan may be reduced. Scan again with the door closed for best scanning quality. 4 Initiate the scan from your software. The software will prompt you when the scan is finished. 2 Insert the carrier gently and firmly into the carrier slot as shown, until you feel it stop. English 14 English 15 8 Preview an Image 1 2 3 4 5 6 7 Select the type of slide or negative you are scanning from the Input list on the Preview panel. [. . . ] Glass-mount 35mm slides cannot be scanned with the four-slide film carrier. Use the single 35mm adapter with the 4x5 carrier. 4 Connect the Scanner to the Computer (Page 6) The SprintScan 45 Ultra scanner SCSI address is set to 6 at the factory. Do not change it unless another device is using that address. Do not use address switch setting 7, 8 or 9. English 4 English 5 The 120 Film Adapters (Page 11) Steps 3 and 4 on pages 11 and 12 have changed to the following: 3 Orient the 120 film adapter with the correct side up and the notches (a) on the left. [. . . ]