User manual POLK AUDIO ATRIUM 65SDI

[. . . ] Unique Dual Input/Single Input Feature: A simple switch, and its ingenious Dual Tweeter Array, allows the Atrium65SDI to be used either as a single high performance stereo loudspeaker, or the left-or-right speaker in a high performance stereo pair!5cm) long throw Polypropylene Cone driver with Butyl Rubber Surroundfor robust bass response. Two 1" (25mm) Dome Tweeters with Neodymium Magnets for accurate high frequencies. Power Port bass venting for deep, low distortion bass. [. . . ] Drive screws into stud or wall anchors, leaving screw heads protruding 1/8" (3 mm). If speaker wire is being fed from a hole in the wall behind the bracket, pull this speaker wire through the hole in the bracket before mounting the bracket [figure 11]. Line up the bracket, attached to the speaker, so that the screw heads pass through the large center hole of the bracket's keyhole slot. Let the speaker and bracket slide straight down, allowing the screw head to slip behind the smaller end of the keyhole slot [figure 12]. Tug gently on the speaker to make certain that the screws and bracket are properly aligned and that the wall anchors are secure. If the bracket is not held snug against the wall by the screw heads, remove the speaker from the wall, drive the screws in a little further and then remount the speaker. Once the speaker is mounted, the bracket knobs can be loosened to "aim" the speaker, and then hand-tightened to keep the speaker angled correctly [figure 14]. Follow the hookup directions included with your receiver. Strip 1/2 inch of insulation from each of the two conductors of the wire to expose the bare metal and twist each of the conduc tors into a single unfrayed strand (so you have two unfrayed strands). Note that one of the terminals on the rear of each speaker is red (+) and the other is black (-). Make certain that you connect the wire from the red terminal of your amplifier or receiver to the red terminal on your speaker and the wire from the black terminal of your amplifier or receiver to the black terminal on your speaker [figure 16]. Most wire has some indicator (such as color-coding, ribbing or writing) on one of the two conductors to help you maintain consistency. Vous pouvez le faire en retirant les boutons du support de l'enceinte et en la dégageant du support, ou en laissant l'enceinte dans son support [figure 9]. Si le fil de haut-parleur destiné à l'enceinte est passé dans le mur et sort derrière le support, passez le fil à travers le trou du support avant d'installer le support au mur [figure 11]. FIGURES 12a & b Use #10 screw for wall stud, use #10 wall anchors + screw for no wall stud. Use tornillos n° 10 si la pared tiene parales internos, use anclas de pared y tornillos n° 10 si la pared no tiene parales internos. FIGURE 11 Feed speaker wire from wall through bracket wire hole for easy mounting. FIGURE 12 Slide the bracket down on the screw heads to catch the keyhole slots. 6 Get more information and exclusive accessories, visit www. ALTERNATE SECURE MOUNTING For more solid mounting, screw the bracket directly into a weight-bearing stud on the mounting surface. Attach and remove the speaker from the permanently secured bracket by tightening and loosening the bracket knobs [as shown in figure 14]. NOTE: If placing your Atrium60 vertically on a surface, please attach 2 feet (included in accessary bag) to bottom of each speaker. [. . . ] For further detailed information, please contact the retailer where you purchased this product or the Polk Audio Importer/Distributor in your country. A listing of Polk Audio Importer/Distributors can be found on the Polk Audio website www. Products must be shipped in the original shipping container or its equivalent; in any case the risk of loss or damage in transit is to be borne by you. If upon examination at the Factory or Polk Audio Authorized Dealer it is determined that the unit was defective in materials or workmanship at any time during this Warranty period, Polk Audio or the Polk Audio Authorized Dealer will, at its option, repair or replace this Product at no additional charge, except as set forth below. [. . . ]