User manual POLK AUDIO RM30

[. . . ] SPEAKER PLACEMENT CENTER CHANNEL SPEAKER (Figure 1) Place the center channel speaker as close to your TV as possible (Figure1). The most popular placement for the center channel speaker is right on top of your TV set. The small size and slender design of the RM7000 Series center channel speakers makes them easy to mount on the wall directly above your TV. They look especially nifty if you have a slim line or flat screen TV. [. . . ] If there is no stud behind the wall at the chosen location, install #10 wall anchors (not supplied) into the wall by following the wall-anchor-manufacturer's instructions (Figure 11b). For masonry walls, use a masonry drill bit and #10 masonry anchor and screw (not included). Tighten screws into stud or wall anchors, leaving screw heads protruding 1/16" (1. Line up the keyhole slots on the bracket so that the screw heads pass through the large center hole of the slots. Let the speaker slide straight down, allowing the screw head to slip behind the smaller end of the keyhole slot (Figure 12). Tug gently on the speaker to make certain that the screws and bracket are properly aligned and that the wall anchors are secure. If the bracket is not held snug against the wall by the screw heads, remove the speaker from the wall, drive the screws in a little further and then remount the speaker. We recommend the following settings as starting points, but the settings that are best for you depend upon your speaker placement, electronics and personal taste. After you've become familiar with what the settings do, experiment with alternate options to find the method that works best for your system setup. R M 7 2 0 0 A C P O W E R (Figure 13) The RM7200 Powered Subwoofer has a built-in power amplifier and must be plugged into a standard household AC power source in order to operate. The power switch has three positions: "On, " "Off" and "Auto" (Figure 13). R M 7 6 0 0 S U B W O O F E R L E V E L C O N T R O L (Volume) Subwoofer level (volume) is adjusted via the knob on the front of the subwoofer under the logo pod. This lets you adjust the level of bass easily after you have made the more complex adjustments on the rear of the Subwoofer. To set level, play a piece of music that has an average amount of bass content. Adjust for deep, powerful bass without "boominess. " RM7600 SETTINGS On the back of the subwoofer (Figure 14), you will see the following controls: Variable crossover control Phase toggle switch +3dB bass boost switch High Pass Filter toggle switch (You will never need to change this out of the "0" position. ) The Subwoofer Level Control is found under the logo pod on the front of the subwoofer. It only effects signals that are sent through the low level, subwoofer and Speaker Wire inputs. It has no effect on signals fed into the LFE input (and you shouldn't be using that input anyway). R M 7 6 0 0 R E C O M M E N D E D S E T T I N G S -- O N W A L L & O F F W A L L (Figures 14, 15 & 15b) Mounting your right and left front satellites on the wall tends to increase their low-midrange response (the low range of a male voice). Mounting them on stands away from the sides of the room tends to decrease their low-midrange response. If you mount the satellites on the wall, we recommend setting your variable crossover control (see Figure 14) at a lower setting (Figure 15a). [. . . ] Use #10 screw for wall stud, use #10 wall anchors + screw for no wall stud. Use tornillos n° 10 cuando haya parales internos en la pared, use to rnillos y anclas n° 10 cuando no haya parales internos. RM30 Center RM7200 Subwoofer RM7200 System RM4300 Satellite RM4600 Center 80Hz-23kHz 115Hz-20kHz 80W NA 20-125W 20-125W 20-125W NA 32Hz-180Hz 32Hz-20kHz 90Hz-25kHz 80Hz-25kHz 28 - 125 Hz 26Hz-200Hz 26Hz-23kHz 65Hz-26kHz 55Hz-26kHz 25 - 180Hz 25Hz-26kHz 28Hz-25kHz 20 -150 Watts/channel 89dB SPL NA NA 89dB SPL 89dB SPL NA 89dB SPL 8 ohms NA NA Compatible with 8 Ohm outputs NA NA Compatible with 8 Ohm outputs NA Compatible with 8 Ohm outputs 165 W Continuous Average Power into 4 Ohms with < 1% THD, 30-200Hz NA (see specification in subwoofer manual for power rating) NA 100W Contiuous Average Power into 4 Ohms with < 1% THD, 30-200Hz NA NA 5. Selectable 80Hz High Pass Filter on the line level outputs vented vented with floorcoupled Power Port NA vented vented Power Port, vented (see individual component's specs) 11 1/4" H x 9 13/16" W x 5 1/2" D (28. [. . . ]