User manual POLYCOM AVAYA 8180 VIEW CERTIFIED CONFIGURATION GUIDE REV A

[. . . ] Information in this document is subject to change without notice and does not represent a commitment on the part of Polycom, Inc. Polycom, Inc. has prepared this document for use by Polycom personnel and customers. The drawings and specifications contained herein are the property of Polycom and shall be neither reproduced in whole or in part without the prior written approval of Polycom, nor be implied to grant any license to make, use, or sell equipment manufactured in accordance herewith. Polycom reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult Polycom to determine whether any such changes have been made. [. . . ] Each command or group of commands is preceded by a sentence indicating the purpose of the command, as in: Enable SNMP services. WC8180(config)#snmp-server enable. Some sections will show additional parameters for setup that are not necessary for phone connection but may be useful in a given specific network situation. They are usually listed at the beginning of a section and are optional. Basic controller configuration Perform the following procedure to place a basic configuration on a WC 8180 device: 1. If the device is not yet running, make sure you have connected serial cable and terminal emulation program. Power up the WC and terminal program will show AVAYA logo on the screen after initial HW boot-up screen. It takes between 4-5 minutes to be network-ready after power-up/reset. Press CTRL + Y and select Command Line Interface. Enter Privileged mode using the enable command. Enter General Configuration mode using the configure terminal command. WC8180#configure terminal 8 PN: 1725-36188-001_A. docx Avaya WLAN Series 8100 5. Specify the system IP address, subnet mask, and default gateway using the IP address command. This command has the following syntax: WC8180(config)#ip address <ip_address> netmask <subnet_mask> default-gateway <default_gateway> WC8180(config)#snmp-server enable. Enter Wireless Configuration mode using the wireless command. Enable wireless capabilities WC8180(config-wireless)#interface-ip <ip_address> WC8180(config-wireless)#enable 12. Enable MDC (mobility domain controller) capability 13. Enter the domain password at the prompt. WC8180(config-wireless)#controller mdc-capable When you are in need of CLI command help, type the command followed by a <space>?, CLI will show list of options available for that command with help. For e. g. , by typing "ip ?" Note: if the AP controller is restored to default settings, the license key must be reinstalled from the serial console using the following: 1. Enter CTRL-Z to return to the admin login state. Type copy tftp license address <X. X. X. X (ip address of the TFTP server) filename <license file name>. Type The rest of the settings in this manual may now be entered from a Telnet interface if desired. Creating a Wireless Mobility Domain Use the existing default VLAN to create a wireless mobility domain. Add the wireless VLAN to it and assign the switch as the active controller for the domain. WC8180#config terminal PN: 1725-36188-001_A. docx 9 VIEW Certified Configuration Guide WC8180(config)#wireless WC8180(config-wireless)#domain <mobility_vlan_name> WC8180(config-wireless)#domain discovered-ap WC8180(config-wireless)#switch <mobility_vlan_name> LVID 1 WC8180(config-wireless)#domain of AP)> mobility-vlan auto-promotevlan-map ap <H. H. H (MAC address Repeat the last command for every AP that will be a member of the network. WC8180(config-wireless)#domain ap-client-qos 2. Join the controller to the domain and define the IP for controlling the AP's: 3. Configure Sub-Option 8 as AVAYA AP with hexadecimal values for domain controller IP addresses. [. . . ] Within the wpa-personal security mode of the Avaya 8180, Polycom phones define two security modes called WPA (TKIP cipher) personal and WPA2 (CCMP cipher) personal within the phone menu system and its HAT(Handset Administration Tool). These phone security modes and the commands to support them in the AP are defined below. Configuring security None WC8180(config-network-profile)#security-mode open Configuring wep-static The Polycom phones support only hex key entry for WEP. WC8180(config-network-profile)#security-mode wepstatic WC8180(config-network-profile)#wep ?key-length Set the number of bits for the WEP keys key-type Set the type WEP key configured key1 Set WEP key #1 key2 Set WEP key #2 key3 Set WEP key #3 key4 Set WEP key #4 transmit-key Set WEP key index used for encryption WC8180(config-network-profile)#wep key-length <40_or_128> key-type hex key<key#> <key_hex_string> transmit-key <key#> Configuring WLAN Settings/ WPA2-Enterprise WC8180(config-network-profile)#security-mode wpaenterprise WC8180(config-network-profile)#radius authenticationprofile <radius_authentication_profile(as defined in section 0) WC8180(config-network-profile)#wpa2 versionssupported wpa2 cipher-suite ccmp Configuring WLAN-Settings/ WPA-PSK Note: only the phone's passphrase method of WPA key definition is supported on the Avaya 8180 AP. ) WC8180(config-network-profile)#security-mode wpapersonal WC8180(config-network-profile)#wpa versions-supported wpa2-and-wpa cipher-suite ccmp-and-tkip WC8180(config-network-profile)#wpa key <passphrase_key_string> PN: 1725-36188-001_A. docx 17 VIEW Certified Configuration Guide Configuring WLAN-Settings/ WPA2-PSK Note: only the phone's passphrase method of WPA2 key definition is supported on the Avaya 8180 AP. ) WC8180(config-network-profile)#security-mode wpapersonal WC8180(config-network-profile)#wpa versions-supported wpa2 cipher-suite ccmp WC8180(config-network-profile)#wpa key <passphrase_key_string> WMM queue priority AP can remark WMM/CoS priority to prioritize legacy clients or clients with incorrect CoS/WMM markings. WC8180(config-network-profile)#wmm2cos 5 6 set to 6 if WMM is video) WC8180(config-network-profile)#cos2wmm 4 5 is 4, packet is assigned to AC_VI) (CoS is (if CoS CLI to create an AP configuration: Finally, using the radius-authentication, radio, and network profiles created, create a new AP Profile and assign unique profile ID: WC8180>enable WC8180#config terminal WC8180(config)#wireless WC8180(config-wireless)#ap-profile <ap_profile_id> Configure AP Model CoS to DSCP Mappings Set a command to its default values Set current profile, as the default profile for an AP DSCP to CoS QoS Mapping End configure mode Exit from AP profile configuration mode Configure Network Profile mapping on a radio Disable AP profile parameters Set an AP profile name Configure Radio Profile mapping on a radio AP Profile Configuration Commands ap-model cos2dscp default default-profile dscp2cos end exit no network profile-name radio Assign name to AP profile: Assign a model to the AP profile: WC8180(config-ap-profile)#profile-name <ap_profile_name> WC8180(config-ap-profile)#ap-model ap8120 18 PN: 1725-36188-001_A. docx Avaya WLAN Series 8100 If Polycom phones are configured for 802. 11a mode, enable the 5GHz radio and assign a unique radio profile ID: WC8180(config-ap-profile)#radio 1 enable WC8180(config-ap-profile)#radio 1 profile-id <radio_profile_id> If Polycom phones are configured for 802. 11b & b/g mixed mode, enabled 2. 4GHz radio and assign unique radio profile ID: WC8180(config-ap-profile)#radio 2 enable WC8180(config-ap-profile)#radio 2 profile-id <radio_profile_id> Assign the network profile for the 5G radio: (Note: the VAP index (second "1" after network) is assumed to be 1. AP profiles may be assigned to AP's in VAP groups. [. . . ]