User manual POLYCOM SPECTRALINK 6000 INSTALLING THE OUTDOOR BASE STATION VERSION F

[. . . ] has prepared this document for use by Polycom personnel and customers. The drawings and specifications contained herein are the property of Polycom and shall be neither reproduced in whole or in part without the prior written approval of Polycom, nor be implied to grant any license to make, use, or sell equipment manufactured in accordance herewith. Polycom reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult Polycom to determine whether any such changes have been made. [. . . ] It supplements the installation documentation for the SpectraLink 6000 System using either the SpectraLink 6300 MCU or the SpectraLink 6100 MCU. Polycom Corporation Model Numbers This document covers the following registered model numbers: RCO400, RCO410, RHO400 Related Documents SpectraLink 6100 MCU: Installation and Operation (1725-36097-001) SpectraLink 6300 MCU: Installation (1725-36122-001) Available at http://www. polycom. com/usa/en/support/voice/proprietary_ wireless/proprietary_wireless. html Contacting Polycom Polycom wants every customer to have a successful installation. Please refer questions to the Customer Support Hotline at (800) 775-5330. The hotline is open Monday through Friday, 6 a. m. Mountain time. 1725-36127-001-F. doc 3 Installing the Outdoor Base Station For Technical Support: technicalsupport@polycom. com For Knowledge Base: http://www. polycom. com/usa/en/support/voice/voice. html For Return Material Authorization: rmacoordinator@polycom. com 4 1725-36127-001-F. doc Contents 0 About this Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Polycom Corporation Model Numbers Related Documents Contacting Polycom 3 3 3 1 2 3 Installing Flush Against a Wall or Hard Ceiling . . . . 6 Installing on an I-Beam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Installing on a Light Pole or Electrical Pole . . . . . . . . . 10 1725-36127-001-F. doc 5 1 Installing Flush Against a Wall or Hard Ceiling Items provided: Items needed: Outdoor enclosure, Base Station 4 anchor bolts (length and type depends on wall or ceiling material Base Station is being mounted to) 1. Mark and drill four holes into the wall or ceiling, using the mounting flanges of the outdoor enclosure as a guide. Mount outdoor enclosure to wall or ceiling using anchor bolts. The outdoor enclosure can be mounted with the compression fitting in any direction. Compression fitting 3. Slide the Base Station cable through the compression fitting and tighten fitting. 6 1725-36127-001-F. doc Installing Flush Against a Wall or Hard Ceiling 4. Crimp an RJ45 onto the Base Station cable using the same wiring guide as the indoor Base Station. Plug the RJ45 into the RJ48C connector. Mounting hole RJ48C connector 6. Place the Base Station into the enclosure with the side of the Base Station with the mounting hole facing the wall or ceiling. The Base Station should fit tightly into the foam blocks. Screw the outdoor enclosure lid back onto the enclosure. 1725-36127-001-F. doc 7 2 Installing on an I-Beam Items provided : Items needed : Outdoor enclosure, Base Station 4 ­ "Caddy" or "B-Line" 3/8" Beam Clamps 4 ­ 1/2" long 1/4" x 20 bolts 4 ­ 2" long 1/4" x 20 bolts 4 ­ 1/4" x 20 nuts 1. Attach a beam clamp to the center of the top and bottom flanges on the outdoor enclosure. Attach a second beam clamp to each of the beam clamps on the enclosure using a 1/2" long 1/4" x 20 bolt and a nut. Attach the outdoor enclosure to I-beam using the beam clamps attached in step 2. See figures in Chapter 1 for pictorial data for the remaining steps: 4. Slide the Base Station cable through the compression fitting and tighten the fitting. Crimp on RJ45 onto the Base Station cable using the same wiring guide as the indoor Base Station. [. . . ] Crimp an RJ45 onto the Base Station cable using the same wiring guide as the indoor Base Station. Plug the RJ45 into the RJ48C connector. 10 1725-36127-001-F. doc Installing on a Light Pole or an Electrical Pole 7. Place the Base Station into the enclosure with the side of the Base Station with the mounting hole facing the pole. [. . . ]