User manual POULAN PRO PPR1742STC

[. . . ] IMPORTANT MANUAL Do Not Throw Away WARNING: OWNER'S MANUAL MODEL: Read this Owner's Manual and follow all Warnings and Safety Instructions. Failure to do so can result in serious injury. PPR1742STC LAWN TRACTOR Always Wear Eye Protection During Operation 173282 11. 29. 99 JH Printed in U. S. A. SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. · · · · · · · · · · · · · · · · GENERAL OPERATION Read, understand, and follow all instructions in the manual and on the machine before starting. [. . . ] Be careful not to allow dirt to enter the engine when changing oil. After oil has drained completely, replace oil drain plug and tighten securely. Refill engine with oil through oil fill dipstick tube. For approximate capacity see "PRODUCT SPECIFICATIONS" section of this manual. Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at "FULL" line on dipstick. OIL FILL CAP/DIPSTICK V-BELTS Check V-belts for deterioration and wear after 100 hours and replace if necessary. Replace belts if they begin to slip from wear. TRANSAXLE COOLING Keep transaxle free from build-up of dirt and chaff which can restrict cooling. OIL DRAIN PLUG ENGINE LUBRICATION Only use high quality detergent oil rated with API service classification SF, SG, or SH. Select the oil's SAE viscosity grade according to your expected operating temperature. SAE VISCOSITY GRADES SAE 30 5W-30 -20° °F °C -30° 0° -20° -10° 30° 32° 40° 0° 10° 60° 20° 80° 30° 100° 40° FIG. 15) Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers. ENGINE COOLING FINS (See Fig. 15) Remove any dust, dirt or oil from engine cooling fins to prevent engine damage from overheating. · Remove hex bolts from blower housing and lift housing off engine. · Cover oil fill opening to prevent entry of dirt. · Use compressed air or stiff bristle brush to thoroughly clean engine cooling fins. · To reassemble, reverse above procedure. HEX BOLTS BLOWER HOUSING HEX BOLTS TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE FIG. 13 NOTE: Although multi-viscosity oils (5W30, 10W30 etc. ) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil. Change the oil after every 50 hours of operation or at least once a year if the tractor is not used for 50 hours in one year. Check the crankcase oil level before starting the engine and after each eight (8) hours of operation. Tighten oil fill cap/ dipstick securely each time you check the oil level. 13 and 14) Determine temperature range expected before oil change. [. . . ] This warranty covers only parts of new Power Train Components which are found upon examination to be defective in material or workmanship as delivered to the original purchaser. This warranty does not cover defects caused by depreciation or damage caused by normal wear, accidents, improper maintenance, improper use or abuse of the product, failure to follow the instructions contained in an Instruction Manual for the operation of the Power Train Component and parts. The cost of normal maintenance and replacement of service items which are not defective shall be paid for by the original purchaser. C. Securing Warranty Service Warranty service can be arranged for by contacting either a Tecumseh Authorized Service Outlet (any Tecumseh Registered Service Dealer, Tecumseh Authorized Service Distributor, or Tecumseh Central Warehouse Distributor) or by contacting Tecumseh, c/o Service Manager, Engine and Transmission Group Service Division, 900 North Street, Grafton, Wisconsin 53024. [. . . ]