User manual PRIMARE CD32

[. . . ] When the disc is paused: stops the disc. When the disc is stopped: opens or closes the CD tray. Press and hold: opens the CD tray. To skip forwards through the tracks · · Press the >/] button on the front panel, or press the ] button on the remote control. Press and hold the >/] button on the front panel, or press the [ button on the remote control. The display shows: To stop play To skip back through the tracks READING followed by the number of tracks and total time: · Press the */å button on the front panel or the remote control. Play/Skip >/] When the disc is stopped: plays the disc. [. . . ] Press the >/= button to start playing from the position you have located. Press the REPEAT button to repeat the Track (T), Folder (F) , or All (A). Press the blue B button to shuffle the tracks within a folder. To scan through a track · · Press the > or SELECT button to display the tracks in the highlighted folder. Press the < button to return to the list of folders. Repeat and shuffle Cd32 user guide teChniCal speCifiCation Every component of the CD32, from the CD transport to the audio output stage, has been designed to achieve the highest possible audio performance. additional information These instructions help you get the best possible sound from your CD32, and give information about configuring its advanced settings. unbalanCed output Voltage: 2. 1 VRMS Impedance: 390 general Mechanism: Asatech 8210. B01-02, Sanyo SFP101N D/A Converter: 2x PCM1704, DF1706 (digital filter), 24/96kHz Frequency Response: 20Hz ­ 20kHz (-0. 5dB) Signal to Noise Ratio: 20Hz ­ 20kHz unweighted -100 dB THD + N: 20Hz ­ 20kHz <0. 01% Power Consumption: Operating 25W, Idle 22W, Standby 0. 5W Dimensions: 430 x 385 x 110 mm Weight: 9 kg Color Options: Black, Titanium phase The phase of the AC supply can make a significant difference to the sound. Ensure that the live pin of the AC power cable is connected to the left-hand pin of the power connector, viewed from the back panel. setting the trigger input and ir input balanCed output Voltage: 4. 1 VRMS Impedance: 47 · · · Press the O button to switch on the CD32. Press and keep holding down the O button. NOTE: You need to keep the O button held down throughout this procedure. When the version number is displayed press the */å button. burn-in Your Primare will start to sound best after an initial burn-in of approximately 24 hours. This product is designed and manufactured to meet strict quality and safety standards. However, you should be aware of the following installation and operation precautions. CAUTION ATTENTION 5. Heat The lightning flash with an arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated 'dangerous voltage' within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, and the point where they exit from the appliance. Locate the appliance away from naked flames or heat producing equipment such as radiators, stoves or other appliances (including other amplifiers) that produce heat. 6. Grounding The appliance has been designed for use in moderate climates. Ensure that the grounding means of the appliance is not defeated. 7. Power lines Only use a rack or stand that is recommended for use with audio equipment. If the equipment is on a portable rack it should be moved with great care, to avoid overturning the combination. Locate any outdoor antenna/aerial away from power lines. 13. Take heed of warnings & instructions Unplug the unit from the mains supply before cleaning. The case should normally only require a wipe with a soft, damp, lint-free cloth. Do not use paint thinners or other chemical solvents for cleaning. We do not advise the use of furniture cleaning sprays or polishes as they can cause indelible white marks if the unit is subsequently wiped with a damp cloth. If the unit has a stand-by function, a small amount of current will continue to flow into the equipment in this mode. Unplug the power cord of the appliance from the outlet if left unused for a long period of time. Safety compliance This product has been designed to meet the IEC 60065 international electrical safety standard. You should read all the safety and operating instructions before operating this appliance. [. . . ] All other servicing should be referred to qualified service personnel. 16. Damage requiring service The appliance should be serviced by qualified service personnel when: A. the power-supply cord or the plug has been damaged, or B. objects have fallen, or liquid has spilled into the appliance, or C. [. . . ]