User manual PRINCETON SEN714

[. . . ] Table of Contents Tips and safety precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Height adjustment, angle adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Connecting the monitor and turning the monitor on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Note - When setting up this monitor for the first time or after having changed an aspect of the current system, perform an automatic screen adjustment before use. (Example: Displayed screen of the L17HMN 00ABA) SCREEN MANUAL MANUAL CLOCK PHASE H-POS V-POS AUTO 127 16 127 32 INPUT-1 ANALOG 1280x1024 V:60Hz H:64. 0kHz Notes - In most cases automatic adjustment is sufficient. - It may not be possible to achieve correct adjustment with the first automatic adjustment. In such a case, try repeating automatic adjustment 2 or 3 times. - If necessary due to any of the following, manual adjustments (P11) can be performed after the automatic adjustment. - When further fine adjustment is needed. - When the computer's video input signals are Composite Sync or Sync On Green. (Automatic adjustments may not be possible. ) - When [OUT OF ADJUST] is displayed. (When the screen displays an entirely dark image, the automatic screen adjustment may be disabled. When marking an automatic adjustment, be sure to either use the Adjustment Pattern or try displaying an image that makes the entire screen very bright. ) - Automatic adjustment may not be achieved correctly depending on what is displayed on the screen ­ moving picture or the MS-DOS prompt etc. 2. The screen will become dark and [ADJUSTING] will be displayed. After a few seconds the SCREEN Menu will return. (The automatic adjustment is now complete. ) 3. Press the MENU button 4 times to make the On Screen Display (OSD) Menu disappear. 10 Adjustment the screen display (When using an analog signal) Manual screen adjustment Adjustments can be made using On Screen Display (OSD) Menu provided. On Screen Display for adjustment This chapter provides the procedure how to adjust the screen by using operation Pattern. The SCREEN Menu will be displayed. SCREEN MANUAL MANUAL CLOCK PHASE H-POS V-POS AUTO 127 16 127 32 Note - Press the button to select [AUTO]. - To choose a menu option: / MODE button - To go to the next menu: MENU button CLOCK This feature will increase or decrease vertical picture alignments. Normally, Automatic Adjustment should be used. ( buttons ) PHASE This feature will increase or decrease horizontal picture alignments. Normally Automatic Adjustment should be used. ( buttons ) NOTE - Adjustments to [PHASE] should be made only after [CLOCK] has been correctly set. INPUT-1 ANALOG 1280x1024 V:60Hz H:64. 0kHz At this point relevant menu options can be adjusted. Each time the MENU button is pressed the next menu is selected. [. . . ] To activate the monitor's Power Management Function, both the video card and the computer must conform to the VESA DPMS standard and the DVI DMPM standard. DPMSDisplay Power Management Signaling DPMS Power Screen consumption H-sync V-sync mode 36W* ON Display on Yes Yes 38W** STANDBY No Yes 1. 6W SUSPEND Display off Yes No OFF No No DMPMDigital Monitor Power Management DPMS mode ON OFF Power consumption Display on 38W Display off 1. 6W Screen No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Function Red video signal input Green video signal input Blue video signal input GND GND For red video signal GND For green video signal GND For blue video signal GND +5V GND N. C. DDC data For Hsync signal input For Vsync signal input DDC clock The DVI-I input connector pin [L17HMN 00ABA] (DVI-I connector with 29 pins) DDC (Plug & Play) This monitor supports the VESA DDC (Display Data Channel) standard. [. . . ]