User manual PRO-JECT PERSPEX 6 SUPERPACK

[. . . ] The power supply socket (13) must line up with the cable channel in the plinth. Make sure the surface you wish to use the turntable on is level (use the supplied spirit level) before placing the turntable on it. Put the plinth where you intend to use the player and level it using the supplied spirit level and the adjustable feet. After this is done remove the three transport screws (1) which secure the sub-chassis (24). [. . . ] The recommended downforce for the factory fitted cartridge is 25mN. 4 © Audio Trade GmbH · Pro-Ject 6 PerspeX SuperPack / Ortofon Valencia · Revision 1. 11. 08/1. 1. 09 Adjusting the azimuth ** The cartridge needle must be vertical in the record groove in order to trace the groove wall modulations correctly. A small screw at the bearing end of the arm allows incorrect azimuth to be corrected if your needle is not mounted exactly perpendicular to the cartridge body (which is often the case). Slacken off the screw just enough to be able to revolve the arm tube without applying force. Do not remove the screw completely! Screw With the aid of a good magnifying glass adjust the needle until it is vertical in the groove (i. e. perpendicular to the record's surface). Ideally this should correspond to the top surface of the cartridge body being parallel to the record surface, but in practice this is often not the case. When you are satisfied that the needle is vertical retighten the screw carefully. Under no circumstances should the arm tube be adjusted with the needle still in the record groove!Irreparable damage may be caused to the cantilever suspension!The arm must be lifted to make each adjustment and lowered afterwards to check it. Anti-skating force adjustment The anti-skating force must be adjusted corresponding to the downforce as follows: Downforce Groove in the stub (15) 10 - 14mN 1st from bearing rings 15 - 19mN 2nd " " " rd 20mN and bigger 3 " " " Hang the loop of the thread of the anti-skating weight in the groove of the anti-skating stub (15) corresponding to the downforce applied to your cartridge and hang the thread in the groove of the wire support (17). Changing replay speed Using the accessory tool provided (3a), hook the belt (3) over the larger diameter part of the motor pulley (2). repeat the proceedings using the smaller step on the pulley. When the Pro-Ject Speed Box ore the Speed Box SE are used speed change between 33 and 45 r. p. m. There is no need to move the belt manually. For detailed product information please refer to the Pro-Ject web site www. project-audio. com. Connection to the amplifier The record player has gold plated female RCA phono sockets (14) so you can substitute the interconnect cables supplied with those of your choice for connection to the amplifier if you wish. Your dealer can advise you on alternative cables. Use the Phono input (sometimes labelled gram, disc or RIAA) on your amplifier. Make sure that the phono input offers correct matching and amplification for the type of cartridge used. Line inputs (such as CD, Tuner, Tape or Video) are not suitable. Take care to connect the left and right channels correctly. The right channel is usually marked red, the left channel black or white. Check the manual supplied with your amplifier for relevant information. An earthing wire may be connected to the screw terminal between the sockets if you encounter hum problems when using the record player. [. . . ] ±0, 5 % ±0, 06 % -73 dB 15-30mN 9 " (230mm) 18mm 2W 16V/500mA AC, suitable for your country's mains supply 460 x 160 x 365mm, dust cover open 460 x 420 x 465mm 10, 5kg 6 © Audio Trade GmbH · Pro-Ject 6 PerspeX SuperPack / Ortofon Valencia · Revision 1. 11. 08/1. 1. 09 Potential incorrect use and fault conditions PRO-JECT turntables are manufactured to the highest standards and undergo strict quality controls before leaving the factory. Faults that may possibly occur are not necessarily due to material or production faults but can sometimes be caused by incorrect use or unfortunate circumstances. Therefore the following list of common fault symptoms is included. The platter doesn't turn although the unit is switched on: The unit is not connected to the mains power supply. [. . . ]