User manual PULSAR NX02

[. . . ] To stop it manually, press any of the buttons. 9 REGULAR ALARM MODE The regular alarm can be set to ring on a 24-hour basis. A English Press to show REGULAR ALARM mode. REGULAR ALARM SETTING 1-AL P M 24 A 10 D C A C D A Press for 2 to 3 seconds. Select the digits to be adjusted (hour/minutes). Return to REGULAR ALARM mode. * The regular alarm mark is automatically displayed and the regular alarm is engaged. ENGAGEMENT/DISENGAGEMENT OF REGULAR ALARM AND HOURLY TIME SIGNAL C 1-AL C P M 24 With each press, the engagement/ disengagement of the regular alarm and hourly time signal are made as follows: Regular alarm engaged Hourly time signal engaged English Regular alarm mark Hourly time signal mark Both engaged Neither engaged * At the designated time, the regular alarm rings for 20 seconds. To stop it manually, press any of the buttons. 11 SINGLE-TIME ALARM MODE The single-time alarm can be set to ring only once at the designated time. [. . . ] Note on unusual display: While setting the time/calendar, all the segments of the display will light up if both buttons C and D are pressed at the same time. Press any one of the buttons to return to the TIME/CALENDAR mode, and then set the time/calendar again. [ANALOGUE TIME SETTING] When setting the minute hand, first advance it 4 to 5 minutes ahead of the desired time and then turn it back to the exact minute. English STOPWATCH MODE Restart and stop of the stopwatch can be repeated by pressing button C. Even if the STOPWATCH mode is changed to another while the measurement is in progress, it continues counting properly. After the stopwatch is used, however, be sure to reset it as the battery energy is consumed enormously to shorten the battery life. 15 TIMER MODE [TIMER SETTING] Before setting the desired time for the timer, reset the digits to "0:00'oo" by pressing button D. The flashing digits move quickly if button D is kept pressed. If the watch is left untouched with the digits flashing, it will automatically return to the TIMER mode in 1 to 2 minutes. [TIMER OPERATION] Restart and stop of the timer can be repeated by pressing button C. Even if the TIMER mode is changed to another while the measurement is in progress, it continues counting properly. After the timer is used, however, be sure to reset it as the battery energy is consumed enormously to shorten the battery life. English 16 REGULAR ALARM MODE [REGULAR ALARM SETTING] The flashing digits move quickly if button D is kept pressed. If the watch is left untouched with the digits flashing, it will automatically return to the REGULAR ALARM mode in 1 to 2 minutes. When the time function is displayed in the 24-hour indication, the regular alarm is also displayed in the 24-hour indication. When setting the hour digits in the 12-hour indication, check that AM/PM is properly set. Only the "PM" mark is displayed. For the AM setting, there is no indication. In the 24hour indication, "24" is displayed. Regular alarm test: The regular alarm can be tested by keeping button C pressed in the REGULAR ALARM mode. After the alarm is tested, press button C to engage/disengage the regular alarm/hourly time signal as desired. SINGLE-TIME ALARM MODE [SINGLE-TIME ALARM SETTING] When button C or D is pressed to set the single-time alarm, the single-time alarm mark "1-AL" is displayed and the single-time alarm is automatically engaged. With each press of button C or D, one minute is advanced or moved back, respectively. If the watch is left untouched in the SINGLE-TIME ALARM mode, it will automatically return to the TIME/CALENDAR mode in 20 to 30 seconds. The single-time alarm rings differently from the regular alarm. English ILLUMINATING LIGHT (Electroluminescent panel) The display remains illuminated if button B is kept pressed. When button B is pressed in the calendar or blank display of the TIME/CALENDAR mode, the time/calendar display is shown while the display is illuminated. [. . . ] Never short-circuit, tamper with or heat the battery, and never expose it to fire. The battery may burst, become very hot or catch fire. English CAUTION The battery is not rechargeable. Never attempt to recharge it, as this may cause battery leakage or damage to the battery. 19 TO PRESERVE THE QUALITY OF YOUR WATCH WATER RESISTANCE Non-water resistant · If the watch becomes wet, have it checked by an AUTHORIZED PULSAR DEALER or SERVICE CENTER. English Water resistant 5/10/15/20 bar · Before using in water, be sure the crown is pushed in completely. · Do not operate the crown and buttons when the watch is wet or in water. [. . . ]