User manual PULSAR V011

[. . . ] 2 Turn Crown clockwise while pressing it lightly until tight. 3 DIGITAL TIME/CALENDAR SETTING A B v Pulsar Press to show TIME/CALENDAR SETTING display. Select the digits to be adjusted. V Set the flashing digits. Press to show TIME/CALENDAR SETTING display. Press to show CALENDAR display. B v A v B v A v QUARTZ A V Selection of the digits TIME/CALENDAR SETTING display ¿ ¿ Seconds ¿ Minutes ¿ Hour ¿ Month Date ¿ ¿ ¿ 12-/24-hour indication 4 Day ANALOGUE TIME SETTING q Be sure to set the digital time first before setting the analogue time. CROWN Pulsar 1 2 1 Pull out when Second hand is at the 12 o'clock position. [. . . ] q If the watch is left untouched in the TIME/CALENDAR SETTING display with the digits flashing, it will automatically return to the CALENDAR display in 1 to 2 minutes. q The calendar automatically adjusts for odd and even months except February of leap years. ¿ 9 ¿ ANALOGUE TIME SETTING q When setting the minute hand, first advance it 4 to 5 minute ahead of the desired time and then turn it back to the exact minute. q When the crown is pushed in, the minute hand may move slightly. However, this is not a malfunction. ALARM q By pressing button B with the alarm setting function activated, the alarm mark is displayed and the alarm is automatically engaged. q When setting the alarm in the 12-hour indication, check that AM/PM is properly set. For the AM setting, there is no indication. q If the watch is left untouched in the ALARM display or with the digits flashing, it will automatically return to the CALENDAR display in 1 to 2 minutes. q Alarm test: Press and hold buttons A and B at the same time in the TIME or CALENDAR display. STOPWATCH q After the stopwatch has measured 60 minutes, it starts counting again from "00' 00" oo" as many times as necessary until it is stopped. q When measuring a long period of time, return the STOPWATCH to the CALENDAR or TIME display after the stopwatch starts, to prevent any possible mistaken operation. 10 BATTERY CHANGE 2 Years Battery life : Approx. 2 years Battery : SEIKO SR726W q If the alarm is used for more than 20 seconds a day and/or the hourly time signal more than 24 times a day, the battery life may be less than the specified period. q As the battery is inserted at the factory to check the function and performance of the watch, its actual life once in your possession may be less than the specified period. q When the battery expires, be sure to replace it as soon as possible to prevent any malfunction. q We recommend that you contact an AUTHORIZED PULSAR DEALER for battery replacement. 11 WARNING q Do not remove the battery from the watch. q If it is necessary to take out the battery, keep it out of the reach of children. If a child swallows it, consult a doctor immediately. q Never short-circuit, tamper with or heat the battery, and never expose it to fire. The battery may burst, become very hot or catch fire. CAUTION q The battery is not rechargeable. Never attempt to recharge it, as this may cause battery leakage or damage to the battery. 12 TO PRESERVE THE QUALITY OF YOUR WATCH WATER RESISTANCE q Non-water resistant · If the watch becomes wet, have it checked by an AUTHORIZED PULSAR DEALER or SERVICE CENTER. q Water resistant 5/10/15/20 bar · Do not operate the crown or buttons when the watch is wet or in water. If used in sea water, rinse the watch in fresh water and dry it completely. · When taking a shower with the water resistant 5 bar watch, or taking a bath with the water resistant 10, 15 or 20 bar watch, be sure to observe the following: * Do not operate the crown or buttons when the watch is wet with soapy water or shampoo. [. . . ] CHEMICALS Be careful not to expose the watch to solvents, mercury, cosmetic spray, detergents, adhesives or paints. may become discolored, deteriorated or damaged. PRECAUTION REGARDING CASE BACK PROTECTIVE FILM I f y o ur w a t c h h a s a protective film and/or a sticker on the case back, be sure to peel them off before using your watch. 15 STATIC ELECTRICITY The IC (Integrated Circuit) used in your watch will be affected by static electricity which may disturb the display. Keep the watch away from close contact with objects such as TV screens which emit strong static electricity. LIQUID CRYSTAL PANEL The normal life expectancy for the liquid crystal panel of the watch is approximately 7 years. 7 Years After that it may decrease in contrast, becoming difficult to read. [. . . ]