User manual PULSAR W650

[. . . ] Return to TIME/CALENDAR mode. The function is on. D v B 4 STOPWATCH MODE B Current time Time measured C D Start / Stop / Restart Reset / Measure lap time Lap time measurement C START D LAP D LAP C D RESET v v v v STOP 5 MEMORY RECALL FUNCTION q The stored data can be recalled either during or after the measurement. B B v Press to activate the memory recall function. ** With each press, stored data are recalled from the oldest to the newest. Return to STOPWATCH mode. D v B D **In memory recall after measurement, the oldest data in memory is displayed. In memory recall during measurement, the newest one is displayed. 6 STROKE MODE (For Cal. W240 and W620) q The number of strokes per minute is automatically calculated by measuring the time required to make three strokes. C C v Press to start measurement. [. . . ] q The first 8 lap times are automatically stored in memory. q Even if the digits are reset to "00" in the stopwatch measurement, stored data is not erased and can be recalled unless a new measurement is started. 12 q Even if the STOPWATCH mode is changed to another while the measurement is in progress, it continues counting properly and the flashing STOPWATCH mode mark indicates that the stopwatch is in use. Lap time STROKE MODE q The time required to make each stroke is measured up to 9 seconds and 99 in 1/100 second increments. q The measurable number of strokes per minute is between 18 and 240. q The stroke and stopwatch functions cannot be used simultaneously. q If the measurement is stopped within 0. 75 seconds after it is started, "- - -" is displayed. If the measurement is not stopped after more than 10 seconds have elapsed, "Err" will automatically appear. Even if "- - -" or "Err" is shown, the measurement can be started by pressing button C. 13 TIMER MODE q The adjustable timer can be set up to 9 hours and 59 minutes in minute increments. W240 and W620: If button D is pressed while the time set for the adjustable timer is displayed, the set time will be canceled and the preset time of 3 minutes will be shown. q Restart and stop of the timer can be repeated by pressing button C. q After the countdown is repeated 99 times, the number of times the countdown is repeated is displayed in 2 digits such as "00" for 100, "01" for 101, and so on. ALARM MODE q At the designated time the alarm rings for 20 seconds, and the display is illuminated as the alarm rings. To stop it manually, press any one of the buttons. q Alarm test: The alarm can be tested by keeping buttons C and D pressed in the TIME/ CALENDAR mode. q When the hourly time signal mark is displayed, the hourly time signal rings every hour on the hour and the confirmation sound beeps with each press of the buttons. ILLUMINATING LIGHT (electroluminescent panel) q The electroluminescent panel loses its luminance as the battery voltage gets lowered. Also, its luminance level decreases gradually with use. 14 BATTERY CHANGE 2 Years Battery life : Approx. W620, W650) q The battery life may be less than 2 years if the alarm is used for more than 10 seconds (Cal. W620, W650) a day and/or the illuminating light more than 2 times (Cal. q As the battery is inserted at the factory to check the function and performance of the watch, its actual life once in your possession may be less than the specified period. q When the battery expires, be sure to replace it as soon as possible to prevent any malfunction. q We recommend that you contact an AUTHORIZED PULSAR DEALER for battery replacement. q Battery life indicator When all the digits start flashing, have the battery replaced with a new one as soon as possible. q Necessary procedure after battery change After the battery is replaced with a new one, or if an abnormal display (broken digits, etc. ) appears, follow the procedure below to reset the IC. 15 Press and hold buttons A, B, C and D at the same time for 2 to 3 seconds. * Before using the watch, set the time/calendar and alarm. [Cal. [. . . ] Temperatures over 50° C (122° F) or below ­5° C (+23° F) may cause a slight time loss or gain or battery leakage or shorten the battery life. However, the above conditions will be corrected when the watch returns to normal temperature. MAGNETISM Your watch will not be affected by magnetism. N S CARE OF CASE AND BRACELET To prevent possible rusting of the case and bracelet caused by dust, moisture and perspiration, wipe them periodically with a soft dry cloth. 18 SHOCKS & VIBRATION PERIODIC CHECK Light activities will not It is recommended that the affect your watch, but be watch be checked once 2-3 careful not to drop your every 2 to 3 years. Have Years watch or hit it against hard your watch checked by an surfaces, as this may AUTHORIZED PULSAR cause damage. DEALER or SERVICE CENTER to ensure that the case, buttons, gasket and crystal seal remain intact. [. . . ]