User manual PULSAR Y911

[. . . ] To stop it manually, press any one of the buttons. q To disengage the alarm: 6 B and C In SINGLE-TIME ALARM mode, press at the same time. v A q Three regular alarms can be set one by one to the desired alarm times. They can be engaged and disengaged independently of one another. DISPLAY CHANGE IN REGULAR ALARM MODE C v A With each press, the display changes in the following order. ALARM-1 ¿ ALARM-2 ¿ HOURLY TIME ALARM-3 ¿ SIGNAL CALENDAR mode ¿ Press in CALENDAR mode to show REGULAR ALARM mode. English ALARM TIME SETTING A v In REGULAR ALARM mode, select the desired alarm display. 7 Mode mark English A Regular alarm mark C Alarm No. * At the designated time, the alarm rings for 20 seconds. [. . . ] q When setting the minute hand, first advance it 4 to 5 minutes ahead of the digital time and then turn it back to the exact minute. q After the crown is pushed back, the digital display changes in the following order: Time ¿ Year ¿ Month, date and day Each of the above displays is shown for 3 seconds. Then, the watch automatically returns to the display you used before setting the time/calendar. Pressing button A, B or C in any of the above displays will also return the watch to the display you used before setting the time/calendar. q Do not leave the watch with the crown pulled out for a long time. Though the hands stop moving, the battery energy is being consumed inside the watch to cause battery depletion. SINGLE-TIME ALARM MODE English q When the alarm time is set by pressing button B or C, the single-time alarm mark is displayed and the alarm is automatically engaged. q The digits move quickly if button B or C is kept pressed. q If the alarm time is set to the current time, the alarm will automatically be disengaged. q The single-time alarm rings differently from the regular alarm. q If the alarm rings when the digital display is blank, the set alarm time is displayed while the alarm is ringing and for a few seconds after it stops ringing. q Please note, if a button is pressed in the STOPWATCH mode to stop the alarm ringing, the alarm is stopped but the stopwatch operation is also made. REGULAR ALARM MODE q If the watch is left untouched in the ALARM SETTING display, it will automatically return to the REGULAR ALARM mode in 1 to 2 minutes. 15 q If the changeover between 12- and 24-hour indications is made in more than one regular alarm display, the time indication system you set last will be effective for the time indication in the other displays. q Note on unusual display: If buttons B and C are pressed at the same time in the ALARM SETTING display, the display as shown at right will appear. Press any one of the buttons to return to the ALARM SETTING display. q The regular alarm rings differently from the single-time alarm. The regular alarm can be tested by pressing and holding button C in the REGULAR ALARM mode. q If the alarm rings when the digital display is blank, the set alarm time is displayed while the alarm is ringing and for a few seconds after it stops ringing. q Please note, if a button is pressed in the STOPWATCH mode to stop the alarm ringing, the alarm is stopped but the stopwatch operation is also made. q If the hourly time signal rings when the digital display is blank, the time of the hourly time signal is displayed while it is ringing and for a few seconds after it stops ringing. English 16 STOPWATCH MODE q q q q Selection of the lap/split displays can be made when the stopwatch is reset to "00". Restart and stop of the stopwatch can be repeated by pressing button B. Lap /split time measurement can be repeated by pressing button C. The turning graphic display only indicates that the stopwatch is measuring and does not show the measured time. q The lap/split times measured by pressing button C and the measurements taken by pressing button B to stop measurement are stored in memory. q The data number is not a lap/split number. [. . . ] bracelet caused by dust, moisture and perspiration, wipe them periodically with a soft dry cloth. English SHOCKS & VIBRATION PERIODIC CHECK Light activities will not It is recommended that the affect your watch, but be watch be checked once 2-3 careful not to drop your every 2 to 3 years. Have Years watch or hit it against hard your watch checked by an surfaces, as this may AUTHORIZED PULSAR DEALER or SERVICE CENTER to cause damage. ensure that the case, crown, buttons, gasket and crystal seal remain intact. CHEMICALS Be careful not to expose the watch to solvents, mercury, cosmetic spray, detergents, adhesives or paints. [. . . ]