User manual PYLE PINV3

[. . . ] · Do not insert foreign objects into this inverter's AC outlets. · Do not leave this inverter or any device operating unattended, to avoid property damage potentially. · Do not use or place this inverter near flammable materials or any places, which accumulate flammable fumes. · Do not connect this inverter to power utility AC distribution wiring under any circumstance. [. . . ] With this lighter plug, the inverter can power loads up to 150 Watts. When continuously powering loads rated higher than 150 Watts, connect the inverter directly to a 12 Volt battery, please use the provided battery clip cables (PINV2/ PINV3) to connect the inverter directly to the 12 Volt power source. the PINV1 is not suitable for operating at power requirement are over than 150 Watts. While using the battery clip cable of PINV2 /PINV3, please follow these steps: A. Cut the lighter plug off the PINV2 / PINV3 power cord. Turn off the power switch and be sure no flammable fumes are present. Connect the BLACK cable to the black post (-) and RED cable to the red post (+) on the rear of the PINV2/PINV3. Then connect the BLACK battery chip to the NEGATIVE (-) terminal and RED battery chip to the POSITIVE (+) terminal of the battery. The reverse polarity connection will result in a blown fuse and may cause permanent damage to the inverter. Do not use the system with positive electrical grounding. Be sure to fasten all connections between battery chips and terminals. 3 -The LED indicators A. GREEN : It indicates the inverter is power on, the cooling fan (PINV2 / PINV3) is also activated, and AC power will be delivered to the AC outlet. RED : It indicates the inverter shutdown caused by low voltage, overload, or excessive temperature. -The ON/OFF switch It enables output AC power at the AC outlet when switched ON. It also acts as a manual reset for overload, low battery voltage and overheat fault conditions. Reset occurs by switching OFF for 5 seconds after automatic shout down then back ON again. This manual reset feature prevents unexpected or hazardous restarting of connected AC loads. -The AC outlet Single and dual AC outlets are provided on one end of the PINV1, PINV2 and PINV3, make sure of the power consumption required before plug in: A. When operated from a vehicle cigarette lighter (PINV1/PINV2/PINV3) A consumption of 150 Watts or less for PINV1, and any combination of 115 Volt AC products with a total power consumption of 150 Watts or less for PINV2 / PINV3. When operated from the directly connection to a 12 Volt battery (PINV2 / PINV3) Any combination of 115 Volt AC products with a total power consumption of 300 Watts or less for PINV2 / PINV3 CAUTION: · Do not connect to AC DISTRIBUTION WIRING. The inverter is designed for connection directly to standard electrical and electronic equipment. · Do not connect the inverter to household or RV AC distribution wiring. · Do not connect the inverter to any AC load circuit in which the neutral conductor is connected to ground (earth) or to the negative of DC (battery) source. -The fuse replacement If the inverter is overload and the spade type fuse is blown, open the fuse replacement cover at the rear of inverter and replace the blown fuse with a new spade type fuse, 20A for PINV1, 35A for PINV2 and 30A X 2 for PINV3. [. . . ] Use the product not exceeds the inverter's surge capacity, 300 Watts (PINV1) , 600 Watts (PINV2) and 800 Watts (PINV3) . Turn off the inverter and allow to cool for 15 minutes. Clear blocked fan (PINV2 / PINV3) or remove the objects covering the ventilation. SYMPTOM B: NO AC POWER OUTPUT, NO LED LIGHTS ARE ON. POSSIBLE CAUSES The lighter socket or 12 Volt outlet has been poor contacted The lighter socket or 12 Volt may require ignition to be on. The fuse of cigarette lighter or 12 Volt outlet is blown The fuse of inverter is blown SUGGESTION Press plug into socket firmly. [. . . ]