User manual PYLE PLA10 Install Guide

[. . . ] high pass frequency control when the crossover selector switch is in "high pass" mode, this control sets the lower frequency limit for audio program sent to the speakers. bass boost level control this control permits adjustment of the bass level up to an increase of approximately 18 dB. low level inputs this amp features gold-plated RCA input jacks for high impedance input. Use these with car stereo output which uses RCA-type connector cables. [. . . ] input level control use this control to match the outputs of your head unit to the amplifier. Starting with your head unit set at about the 2 o'clock position, increase the amp level control until distortion begins to occur, and reduce slightly from this point. low pass frequency control when the crossover selector switch is in "low pass" mode, this control sets the upper frequency limit for audio program sent to the speakers. high pass frequency control when the crossover selector switch is in "high pass" mode, this control sets the lower frequency limit for audio program sent to the speakers. bass boost level control this control permits adjustment of the bass level up to an increase of approximately 18 dB. low level inputs this amp features gold-plated RCA input jacks for high impedance input. Use these with car stereo output which uses RCA-type connector cables. high level inputs if your car stereo lacks RCA-type output jacks, you may connect speaker output leads to these input connectors. power LED this indicator is illuminated when power is applied. protection LED this indicator is illuminated when built-in protection circuitry is activated. power fuse the fuse protects the amplifier and your car's electrical system from short circuit conditions. If using high level inputs, do not use the low level RCA inputs at the same time! using head unit high level inputs L L R R wiring harness from spealer terminals blue wave mono input connections 2 ch amps PLA485·PLA785·PLA1285 using low level inputs pla485 pla785 pla1285 head unit 17 PLEASE NOTE!If using high level inputs, do not use the low level RCA inputs at the same time! To a second amplifier Y Adaptors using head unit high level inputs To a second amplifier L L R R wiring harness wiring harness from spealer terminals blue wave 4 ch amps PLA885·PLA10 4 CH input connections using 2/4 channel input connections low level inputs pla885 pla1085 L/R FRONT Audio Outputs L/R REAR Audio Outputs head unit 18 2 CH input connections using low level inputs L Y adaptors R blue wave 4 ch amps PLA885·PLA10 4 CH floating ground connections high level input connections pla885 pla1085 19 4 CH harness wiring for common ground connections CH 3/4 REAR L ORANGE BLACK BLACK CH 1/2 R L R FRONT ORANGE BLACK BLACK REAR L ORANGE BLACK BLACK R L R FRONT ORANGE BLACK BLACK ORANGE from speaker terminals ORANGE PLEASE NOTE!If using high level inputs, do not use the low level RCA inputs at the same time! ORANGE from speaker terminals ORANGE blue wave mono input connections 4 ch amps PLA885·PLA10 4 CH mono input connections using low level inputs pla885 pla1085 head unit LEFT FRONT Audio Outputs RIGHT FRONT Audio Outputs RIGHT REAR Audio Outputs LEFT REAR Audio Outputs 20 2 CH mono input connections using low level inputs L Y adaptors R blue wave 4 ch amps PLA885·PLA10 4 CH floating ground connections high level mono input connections pla885 pla1085 CH 3/4 21 CH 1/2 R ORANGE BLACK BLACK L ORANGE BLACK BLACK R ORANGE BLACK BLACK L ORANGE BLACK BLACK ORANGE from speaker terminals ORANGE PLEASE NOTE!If using high level inputs, do not use the low level RCA inputs at the same time! 4 CH harness wiring for common ground connections ORANGE from speaker terminals ORANGE blue wave 5 ch amps PLA1585 4 CH input connections using 5 channel input connections low level inputs pla1585 L/R REAR Audio Outputs L/R FRONT Audio Outputs head unit 22 2 CH input connections using low level inputs head unit Y adaptors R L blue wave 5 ch amps PLA1585 4 CH floating ground connections SWITCH POSITION INPUT 4 CH 5 CH high level input connections OUTPUT 5 CH 5 CH pla1585 5 CH 4 CH Attention: Use High Level MOLEX Input for 5CH mode only. 23 5 CH harness wiring for common ground connections CH 3/4 REAR L ORANGE BLACK BLACK CH 1/2 R L R FRONT ORANGE BLACK BLACK REAR L ORANGE BLACK BLACK R L R FRONT ORANGE BLACK BLACK ORANGE from speaker terminals ORANGE PLEASE NOTE!If using high level inputs, do not use the low level RCA inputs at the same time! ORANGE from speaker terminals ORANGE blue wave mono input connections 5 ch amps PLA1585 4 CH mono input connections using low level inputs pla1585 R CH FRONT/REAR Audio Outputs L CH FRONT/REAR Audio Outputs head unit 24 2 CH input connections using low level inputs head unit Y adaptors R L blue wave 5 ch amps PLA1585 4 CH floating ground connections high level mono input connections pla1585 CH 3/4 25 CH 1/2 R ORANGE BLACK BLACK L ORANGE BLACK BLACK R ORANGE BLACK BLACK L ORANGE BLACK BLACK ORANGE from speaker terminals ORANGE PLEASE NOTE!If using high level inputs, do not use the low level RCA inputs at the same time! 4 CH harness wiring for common ground connections ORANGE from speaker terminals ORANGE blue wave speaker connections 2 ch amps PLA485·PLA785·PLA1285 Stereo Output Mode pla485 pla785 pla1285 26 Bridged Mono Output Mode LEFT speaker RIGHT speaker speaker MINIMUM SPEAKER IMPEDANCE 4 OHMS! blue wave speaker connections 4 ch amps PLA885·PLA10 4 CH Output Mode pla885 pla1085 27 Bridged Dual Mono Output Mode L FRONT speakers R L R REAR speakers speakers L R MINIMUM SPEAKER IMPEDANCE 4 OHMS! blue wave speaker connections L 5 ch amp PLA1585 2 CH Bridged Output Mode with Subwoofer Output pla1585 30 MINIMUM SPEAKER IMPEDANCE 4 OHMS!R SUBWOOFER mounting Your new Pyle Blue Wave Series amplifier comes complete with all required mounting hardware. When determining a suitable location in your vehicle for the amp, please remember that it is a high-power electronic device capable of generating high heat. For this reason, always choose a location in your vehicle which has low vibration, adequate ventilation, a minimum of dust, and no moisture. Be sure to mount the amp in such a manner as to allow reasonable airflow over the cooling fins. Mark the location for the mounting screw holes by positioning the amp where you wish to install it and use a scribe (or one of the mounting screws) inserted in each of the mounting holes to mark the mounting surface. [. . . ] Check the Balance control on the head unit (or other source) to verify that it is set to its midpoint. 32 · If the shutdown was a result of an input overload, or speaker short circuit, be sure to correct the condition before restarting. The amplifier can be restarted by turning the remote power OFF and then ON again. If you are using the Low Level RCA input, reverse the input plugs at the amplifier (i. e. , switch the L with the R). If the channels which is silent switches to the other side, the problem is either in the head unit/other source or the connecting cables. Readjust the Input Level Control(s) to better suit the input signal. [. . . ]