User manual PYLE PLCD62

[. . . ] Do not touch the terminals of the units. If you have difficulty in installing this unit in your vehicle. If the unit seems not work in properly press the reset button to reset the memor y of the unit. Attaching panel Attach the front panel by fixing the right side of it into this unit as1 showing. Then push the left side of panel towards into connecting plug as 2 showing. Attaching panel 2 Follow this easy wiring diagram in order to enable you to install the new or existing RADIO and SPEAKER wring system. Be sure the unit is connected to a 12 volts battery with negative ground. [. . . ] Load impedance less than 4 ohms could damage the unit. Never combine (BRIDGE) the outputs for use with 2 speakers, and Never ground any Negative speaker to the chassis ground. GREEN LEFT FRONT Connect to control for antenna or remote control for amplifier. GREEN/BLACK GREY ORANGE RIGHT FRONT YELLOW BLACK LEFT REAR GREY/BLACK BROWN Memor y+ Ground12V+ FUSE Connect to battery or +12 volts of power source that is always live. BROWN/BLACK BLUE Connect to lgnition key switch. RED RIGHT REAR 3 BLUE/BLACK Before installing the receiver permanently, fit it in the approximate place in your car Connect the equipment according to the speakers and electrical connections. When your system is operated properly, (preferably with the car engine running), follow the instructions for permanent installation of your system. 3)Support strap (supplied) INSTALL THE UNIT 1)Install half sleeve, can be with or without adapter. 2)Bend over some tabs where possible tosecure the half sleeve inside of dash. 3) Support strap to bestrutted under dash, secure this strip to avoid skipp ing of disc. 2)Bend over tabs of half sleeve (supplied) 1) Adapter (not supplied) REMOVING THE UNIT Insert removal wrench into the small gap on the right side of the unit and pull the unit slightly out on the same side, then release the wrench. Repeat the same action for the left side. By now, you can remove the unit and unplug the wires connector. Half sleeve (supplied) 4) Two wrenches for release the unit (supplied) 4 EJECT SEL/VOL Volume/Push sel Increasing volume VO VO EJECT E Rotate the [VOL+]button Decreasing SEEK PUSH SEL BAND L- L+ PUSH SEL BD MODE ST S LOC L AUX IN EQ CLOCK SCAN REPEAT SHUFFLE 1010+ VOL POWER Rotate the [VOL-]button VOL MD LOUD E C 1 2 3 4 5 6 P LD EQ CLOCK POWER LOUD Eject LOC ST LOUD Out CH Press the [EJECT]button to eject the disc out of the unit . LCD display EJECT Power Tur ning ON the power Press the [PWR]button. Press [power] button to turn on/off the unit. Release press the " " button to release faceplate. To install it again, please do it left side first, then right. 5 Hour MODE When CD disc in unit , press [MODE], it will switch between: Rotate [VOL+/-]button to adjust the hour. Minute BAND BAND CD USB USB AUX IN AUX IN BAND BAND Press [SEL] then Rotate [VOL+/-] button to adjust the minute. Quit clock set mode No CD disc in , press [MODE], it will switch between: If there is no operation in 5 seconds, it will quit clock set mode. EQ DSP EQ setup LOUD DSP LOUD press the [LOUD]button to add bass output, and press it again to cancel it. Rotate VOL to volume adjustment. USB player Plug USB, then press [MODE]to transfer to USB play. , select: Under USB play, press , can select tracks, REPEAT: Press [REPEAT] button first to repeat the playing track continuously. PLAY/PAUSE: press PLAY/PAUSE button to play or pause. 9 SEEK+ SEEK- BAND Tune In radio mode: EJECT E PUSH SEL manual tuning: BAND SEEK BD MODE ST short press Short press button it can select higher frequency station. can select lower frequency station. S LOC EQ CLOCK SCAN REPEAT SHUFFLE 1010+ VOL POWER MD LOUD L AUX IN E C 1 2 3 4 5 6 P LD Auto loading tuning: the long press button it can automatically select higher frequency station. And long press can automatically select lower frequency station. LOC MONO Band Selecting band Press BAND button to select among three FM or two AM bands. (FM1-FM2-FM3-AM1-AM2) ST In FM band mode, press the ST key. Each time you press the key, you switch between position and stereo position. MONO FM1 FM2 FM3 if the unit has received stereo signal in FM band in stereo position. The LCD indicate ST . AM2 AM1 Loc In radio mode, press this button to switch between LOC/DX functions and LOC shown on the display indicates that LOC function is on. LOC is local frequency receipt DX is distance frequency receipt 10 Loading and replacing the batter y POWER MUTE PLAY/PAUSE Use one lithium battery(CR2025) insert the batteries with the +and - poles aligned properly. [. . . ] Following the illustration inside the case. EQ 1 5 9 LOD 2 6 10/0 3 7 10+ ST 4 8 APS Pull out BND Store unused batteries out of the reach of children. Contact a doctor immediately if the battery is accidentally swallowed. Do not set the remote on hot places such as above the dashboard. SEL CLK LOC CD USB AUX Basic operation Tur ning ON the power RPT SCN RDM CD/MP3&USB Press the [ ]button. Press to turn on the unit power, Press the button to turn off the unit. 11 Volume Increasing volume Exter nal view . . . . . . . . Number of items Exter nal view . . . . . . . . [. . . ]