User manual PYLE PLCDCS200

[. . . ] · LOUDNESS Press the LOUD button (3) to loudness function and display will show "LOUD". Press it again to release this function. · DISPLAY Press the DSP button (15) can switch between frequency or play time display and clock display. To set clock, hold down DSP button (15) until the clock is shown on display then press TUNE/TRACK/SKIP button (17) to change hours or TUNE/TRACK/SKIP button (16) to change minutes. 6 Press EQ button (12) over 1 second, graphic display type will display on the LCD and then press TUNE/TRACK/SKIP button (16) or TUNE/TRACK/SKIP button (17) to select graphic display type as follows: DNCO1 DNCO2 DNCO3 DNCO4 DNCO5 · REMOTE SENSOR Point the remote control handset to the remote sensor IR (23). [. . . ] · EJECT Push the eject button (24) down to eject the cassette tape. · CASSETTE COMPARTMENT Insert a cassette tape into the cassette compartment (26). The cassette mechanism will load it in play mode. OPERATION CDP OPERATION · SELECT TRACKS Press TUNE/TRACK/SKIP button (16) or TUNE/TRACK/SKIP button (17) to move to the previous track or the following track. Hold TUNE/TRACK/SKIP button (16) or TUNE/TRACK/SKIP button (17) to fast reverse or fast forward. CD play starts from when you release the button. · PAUSE PLAYING Press PAU button (19) to pause CD player. · REPEAT THE SAME TRACK Press RPT button (21) to continuously repeat the same track. · PREVIEW ALL TRACKS Press SCN button (20) to play first several seconds of each track on the current disc. Press it again to stop intro and listen to track. · PLAY ALL TRACKS Press RND button (22) to play all tracks on CD in random order. · EJECT When the front panel is folded down, press eject button (4) to stop CD playing and eject the disc from the disc slot (5). REMOTE CONTROL HANDSET 1 7 4 3 8 6 13 12 11 15 9 5 2 10 14 FUNCTION KEYS & CONTROL 1. TUNE/SEEK 10. EQ 11. PRESET 12. PAU 13. SCN 14. RPT 15. RND = = = = = = = = = = = = = = = Power Button Mute Button Select Button Volume Up Button Volume Down Button Band Select Button Mode Button Tune/Seek Down Button Tune/Seek Up Button Preset Equalization Button Preset Buttons Pause Button Scanning Button Repeat Button Random Button 8 SPECIFICATIONS GENERAL Power Supply Requirements Chassis Dimensions Loading Impedance Maximum Output Power Current Drain : : : : : DC 12 Volts, Negative Ground 200 mm (W) x 138 mm (D) x 75 mm (H) 4 - 8 per channel 4 x 50 Watts 10 Ampere (max. ) CD PLAYER Signal to Noise Ratio Channel Separation Frequency Response : More than 55 dB : More than 50 dB : 20 Hz - 20 KHz CASSETTE PLAYER Tape Speed Fast Forward Time Frequency Response Channel Separation Crosstalk Wow and Flutter : : : : : : 4. 76 cm/sec 180 seconds (C-60 type) 50 to 8, 000 Hz > 35 dB > 40 dB 0. 35% WRMS RADIO Frequency Coverage I. F. Sensitivity (S/N = 30 dB) Image Rejection Stereo Separation Frequency Coverage I. F. Sensitivity (S/N = 20 dB) : : : : : FM 87. 5 to 107. 9 MHz 10. 7 MHz 3 µV > 45 dB > 30 dB AM : 530 to 1710 KHz : 10. 71 MHz : 32 dBu 9 TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Cause The car ignition switch is not on. Solution If the power supply is properly connected to the car accessory circuits, but the engine is not moving, switch the ignition key to "ACC". Disc cannot be loaded or ejected. Presence of CD disc inside Remove the disc in the player, then the player. Inserting the disc in reverse direction. Compact disc is extremely dirty or defective disc. Insert the compact disc with the label facing upward. Clean the disc or try to play a new one. [. . . ] It is very important to understand the difference. AM reception will deteriorate when passing through a tunnel or when passing under high voltage lines. Also, noise can be picked up from passing automobiles. Although AM is subject to environmental noise, it has the ability to be received at great distance. [. . . ]