User manual PYLE PLCDCS300

[. . . ] Press it again to release this function. · DISPLAY Press the DSP button (15) can switch between frequency or play time display and clock display. To set clock, hold down DSP button (15) until the clock is shown on display then press TUNE/TRACK/SKIP button (17) to change hours or TUNE/TRACK/SKIP button (16) to change minutes. · SELECT MODE Press the MODE button (6) to choose desired listening mode. [. . . ] Press CD OPEN/CLOSE/EJECT button (4) again or POWER button (9) to slide up the front panel. When the front panel slides down, insert a disc into the disc slot (5), the front panel will automatically slide up. If there has a disc in, when the front panel slides down, press CD OPEN/CLOSE/ EJECT button (4) for over 1 second to stop CD playing and eject the disc from the disc slot. · REPEAT THE SAME TRACK Press RPT button (21) to continuously repeat the same track. · PREVIEW ALL TRACKS Press SCN button (20) to play first several seconds of each track on the current disc. Press it again to stop intro and listen to track. · PLAY ALL TRACKS Press RND button (22) to play all tracks on CD in random order. Press it again to cancel the function. · SELECT TRACKS Press TUNE/TRACK/SKIP button (16) or TUNE/TRACK/SKIP button (17) to move to the previous track or the following track. Hold TUNE/TRACK/SKIP button (16) or TUNE/TRACK/SKIP button (17) to fast reverse or fast forward. CD play starts from when you release the button. · PAUSE PLAYING Press PAU button (19) to pause CD player. Press it again to resume play. 9 OPERATION REMOTE CONTROL HANDSET 1 7 4 3 8 6 13 12 11 15 9 5 2 10 14 FUNCTION KEYS & CONTROL 1. TUNE/SEEK 10. EQ 11. PRESET 12. PAU 13. SCN 14. RPT 15. RND = = = = = = = = = = = = = = = Power Button Mute Button Select Button Volume Up Button Volume Down Button Band Select Button Mode Button Tune/Seek Down Button Tune/Seek Up Button Preset Equalization Button Preset Buttons Pause Button Scanning Button Repeat Button Random Button 10 SPECIFICATIONS GENERAL Power Supply Requirements Chassis Dimensions Loading Impedance Maximum Output Power Current Drain : : : : : DC 12 Volts, Negative Ground 200 mm (W) x 138 mm (D) x 100 mm (H) 4 - 8 per channel 4 x 50 Watts 10 Ampere (max. ) CD PLAYER Signal to Noise Ratio Channel Separation Frequency Response : More than 55 dB : More than 50 dB : 20 Hz - 20 KHz CASSETTE PLAYER Tape Speed Fast Forward Time Frequency Response Channel Separation Crosstalk Wow and Flutter : : : : : : 4. 76 cm/sec 180 seconds (C-60 type) 50 to 8, 000 Hz > 35 dB > 40 dB 0. 35% WRMS RADIO FM 87. 5 to 107. 9 MHz 10. 7 MHz 3 µV > 45 dB > 30 dB Frequency Coverage I. F. Sensitivity (S/N = 30 dB) Image Rejection Stereo Separation Frequency Coverage I. F. Sensitivity (S/N = 20 dB) : : : : : AM : 530 to 1710 KHz : 10. 71 MHz : 32 dBu 11 TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Cause The car ignition switch is not on. Solution If the power supply is properly connected to the car accessory circuits, but the engine is not moving, switch the ignition key to "ACC". Disc cannot be loaded or ejected. Presence of CD disc inside Remove the disc in the player, then the player. Inserting the disc in reverse direction. [. . . ] It is very important to understand the difference. AM reception will deteriorate when passing through a tunnel or when passing under high voltage lines. Also, noise can be picked up from passing automobiles. Although AM is subject to environmental noise, it has the ability to be received at great distance. [. . . ]