User manual PYLE PLDF7IN

[. . . ] Do not open the CD changer or try to make any change. It is very complicated, and it uses laser adapter to read information out of CD surface. Try to avoid the laser because of it is still there. Brief Introduction Thank you for purchasing this series of high quality AV products for automobiles. This product is a multi-function system developed by our company and special for high-level cars, business vehicles and special-use vehicles and has a car-carried control center concentrating entertainment, audio-visual, radar distance test, rear view and TV as a whole. [. . . ] Press or (18) for time adjusting, press or (18) for change-over selection between HOUR and MINUTE. Press SET directly to exit without storing the setup. vertically after that to confirm and store the time setup, (18) vertically to confirm entering into time setup mode. The screen will display as the TIME ADJ 12:00 5. 5 Monitor angle adjust When the system is ON , short pressing can adjust the display angle to the preset angle or return to vertical mode. A. When the system is under non-DVD mode, the display angle status can be vertical preset angle; B. When the system is under DVD mode, the display angle status can be vertical preset angle max. When the system is ON , pressing on the remote board can tune the display angel to bigger or smaller; The preset angle of the display can be set in the System Menu (refer to 5. 3. 1), under non-DVD mode, or also can be used to preset angle. Radio operation 6. 1 Receive pre-stored stations Press RADIO to enter into radio mode and play back the pre-stored radio channels, please see the right picture. Press or to play the pre-stored last or next radio channel; RADIO FM - - M 2 90. 6MHz M1 M2 M3 M4 M5 M6 M7 M8 Press the digital keys (1~8) on the remote board, directly play the corresponding pre-stored radio channel; Volume adjusting please refer to 5. 2; Select other functions(AV, TV, DVD, CDC) to stop playing radio. 6. 2 Frequency Switch Press button BAND, you can choose FM(FM1/FM2) and AM. 6. 3 Searching station A. Manual search Press each step; Pressing (>2S) or longer will initiate the automatic search or last/next radio channel; press SEEK or reverse search key to end manual search. The current receiving frequency will be displayed on the screen. B. Automatic search Pressing SEEK two times continuously (3S)under receiving status will enter into automatic search mode. Search for all the radio channels within the frequency in order and store automatically. During the search, the changed frequency will be displayed on the screen. Check equipment top and the direction of disc insertion, push CD changer inside gently until a sound of click. Close door until you hear a sound of click. Make sure to close CD changer door closely to prevent dusty enter. 9. 6. 4 Remove disc box Screw ignition key turn on receiver power. Press ejection button , CD changer will be ejected out. Draw out CD changer according to arrow direction, until CD changer glides out of equipment. CAUTION: If in any case, the CD changer can not be draw out, press RESET button and push the CD changer inside with strength, then press ejection button . , AV operation 10. 1 AV play Press AV button, start playing A V select other function(TV Radio DVD CDC), stop playing AV. Note: The AV input channel is commonly used with car-backing scene, if you use AV function, please set the BACK in Sys Setup to OFF (refer to 5. 3. 3 in detail) . 10. 2 Backing with backsight If you want to use the rear-view function at backing, please set BACK in Sys Setup to ON (refer to 5. 3. 3 in detail). If the A interface loses efficacy, the signal can not be V input. When the car converters into BACK, no matter what condition the system is in, it will automatically transfer to back view display, the screen will display will restore automatically. After leaving the BACK mode, all the functions of the system , Necessary Disc machine installation In Example of Panasonic DP88 11. 1 Appearance 11. 1. 1 CD changer AH C V Door Reset Compact disc area Eject Angel Adjust Screw There are two angel adjust screws for both sides. 11. 1. 2 Compact disc and tray Compact disc inserting direction B Tray D IG CAUTION Do not use a disc with 8cm diameter. Tray should be placed in the right position before inserting compact disc. D ii s Ds ITA A LA UD D c CO IO MP M AC T 11. 2 Installation guidance 11. 2. 1 Installation location When the temperature in car is too high, do not install this instrument on rear undercarriage to avoid the problems, in case it is caused by the contact with it. The following locations also should be avoided, Direct sunshine hot air from heater or other high temperature places. Too much humid, dirty or dusty. 11. 2. 2 Installation work According to your selected installation angle, use a screwdriver to adjust the angle-adjustment screw to a position of V or H When set to vertical position Choose V position. When set to horizontal position Choose H position. [. . . ] The dirt should be wiped off by using soft cloth. Please don't let the display screen be disposed in insulation. If water or other substances enters into the product, please turn off the power supply immediately and contact the distributors or us. Please turn off the power supply first when you plan to clean the machine. [. . . ]