User manual PYLE PLRDVD10

[. . . ] You can manually adjust the brightness of the display according to the prevailing light conditions of the surroundings. The backlighting control produces sharp contrast images free from reversed or blurred colors. This unit has 1 Audio/Video input, 1 Audio/Video output, for connection additional monitor and IR transmitter of IR wireless headphone. You can use wired headphones and infrared wireless headphones with this unit. 2 Precautions To avoid the risk of serious injury or accident, read the following precautions before installing and operation the unit. [. . . ] Installing this unit with the ignition on may cause battery drain or a short circuit. Do not damage any pipes, tubes, the fuel tank or electric wiring when installing this unit. If you drill a hole in car panels, make sure that any hidden car parts will not be damaged. Do not use any nuts or bolts for safety devices such as steering linkage, fuel supply or braking systems. This can cause a fire or an accident. 3 Where to Install Before installing this unit, please check your local traffic rules and regulations. Follow the diagram below to install this unit in a suitable position in your car. Do not install this unit where: It will obstruct the driver's view when the monitor is in either the open or closed position. It will obstruct the operation of the airbag system. It will obstruct the operation of the vehicle, especially the steering wheel, shift lever, or brake pedal. A driver or passengers may injure themselves when getting into or out of the car. 4 Installation Roof-mount Installation/Installation on ceiling Securlock Press the RELEASE BUTTON to open the Display Monitor 5 Setting Up Dome Lamps *Operating the dome There are there function buttons for the Dome lamps operation: OFF, DOOR, and ON. DOOR: To make the lamps turned on only when car doors are opened. C. *The electric circuit figure Point R W B Power Cord Color Red White Black Connection Connecting with Power Supply Connecting with Sensor of Car Doors For Ground Connection Remarks: 1. There is no wiring connection necessary at " B " point as " B " has been connected when the metal bracket is screwed in. Only use 12 Volt DC power. 6 MONITOR SECTION Remote Control Holder 6 5 4 3 2 1 ¢Ù ¢Ú ¢Û ¢Ü ¢Ý ¢Þ IR Sensor Power OSD UP Down Mute 7 * OSD MENUS IN A/V SOURCE * Quick Adjustment OSD Menus 1. press " MENU" button, to open the MAIN MENU, using "+ " or " - " buttons to select OSD functions. In order to select desire options, it is necessary to press "MENU" Again to enter each mode, then use" + / - " to increase or decrease Parameters as well. Press " + " or " - " button directly to adjust speaker volume 3. Selecting " EXIT" mode will store your selected parameter and leave OSD Menus. 8 DVD SECTION To operate DVD by pressing the buttons on front panel: ¢Ù ¢Ú Eject: Ejecting a Disc, Press (EJECT) button to eject the disc Stop: Stopping Play, Press the (STOP) button to stop the unit playback, when you press the (PLAY) button it will continuous normal playback. Press the (STOP) button twice, it will stop the playback and go back to initial Track/Chapter. ¢Û ¢Ü Play/Pause: Press once to pause a play, press again to resume or continuous playback. Power: Press the (POWER) Button, Insert the disc with printed side facing up into the disc slot, The player starts playback automatically. ¢Ý ¢Þ Reverse: Press (REW) to reverse rapidly. Forward: Press (FF) to forward rapidly. 9 To Operate DVD by Remote Control 1. REPEAT: Repeat playing the current chapter. [. . . ] LANGUAGE: Choose different output language. PROGRAM: Arrange program. Preparing the Remote Control Inserting the Batteries 1. Make sure that the positive and negative terminals of the batteries are oriented indicated. Close the cover Battery: Two AAA size batteries. [. . . ]