User manual PYLE PLTV165

[. . . ] 10 Open/close the monitor and angle adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Remote sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 6. 5 inch TFT display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Reset function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause Malfunctions. Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the Vehicle. Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a sudden stop, like an emergency stop. If installation angle exceeds 30 from horizontal, the unit might not give its optimum performance. O TAKE OUT SCREW BEFORE INSTALLATION Before install the unit, please remove the two screws on the back of the unit. Take out screw before installation. DIN FRONT-MOUNT (Method A) Installation Opening This unit can be installed in any dashboard having an opening as show below: 53mm 182mm Installing the unit Be sure you test all connections first, and then follow these steps to install the unit. 1. Make sure the ignition is turned off, and then disconnect the cable from the vehicle battery's negative (-) terminal. Disconnect the wire harness and the Antenna. Lift the top of the outer trim ring then pull it out to remove it. The two supplied keys release tabs inside the unit's sleeve so you can remove it. One key is for the right side and the other is for the left side. Insert the keys as far as they will go (with the notches facing up) into the appropriate slots at the middle left and right sides of the unit. Then slide the sleeve off the back of the unit. 30 Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration. DIN FRONT/REAR-MOUNT This unit be can properly installed either from "Front"(conventional DIN Front-mount) or "Rear"(DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods. 4 INSTALLATION Sleeve L Key Outer Trim Ring (Tapping Screw (5x25mm) and Plain Washer) to attach the other end of metal strap to a solid metal part of the vehicle under the dashboard. This strap also helps ensure proper electrical grounding of the unit. R Key Spring Washer Hex Nut 5. Mount the sleeve by inserting the sleeve into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver. Not all tabs will be able to make contact, so examine which ones will be most effective. Bending open the appropriate tabs behind the dashboard to secure the sleeve in place. Dashboard Tabs Metal Strap Mounting Bolt Plain Washer Tapping Screw 9. Reconnect the cable to the vehicle battery's negative (-) terminal. Then replace the out trim ring. Removing the unit Screwdriver any wires or cables. Sleeve 6. Reconnect the wire harness and the antenna and be careful not to pinch any wires or cables. Slide the unit into the sleeve until it Locks into place. To further secure the unit, use the supplied metal strap to secure the back of the unit in place. [. . . ] Press digital select button (-/--) () cooperatively used with numeric buttons to select channel desired. For example, when you want select 16 channel, press -/-- (28) to switch between "-" and "--", when the "--" appears on the display, you can press "1" button then press "6" button to select 16 channel. 6. 5 inch TFT DISPLAY When the monitor stretches out, the 6. 5 inch color TFT display (6) can show the current state of the unit. RESET FUNCTION Reset button (7) must be activated with either a ballpoint pen or thin metal object. The reset button is to be activated for the following reasons: Initial installation of the unit when all wiring is completed. All the function buttons do not operate. [. . . ]