User manual PYLE PLTVD122

[. . . ] DVD Player Operating Instructions PLTVD122 NOTES Any change to the design and specifications will not be advised. Before attempting to connect, or operating this product. Please read the instructions completely Important Precautions Table of content The design and manufacture of this player takes personnel safety in to consideration. However, any improper operation may result in electric shock, fire and other hazard. So Please adhere to following precautions. 1 DVD features _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 Names of parts 1 Safety precautions There is dangerous voltage inside this product, do not open the cabinet by yourself to prevent electric shock. [. . . ] Please refer to the description on [SETUP] setting menu for the information on the switching of play modes. In the first play mode, after a disc is put into the player and the player reads the disc, the player will go into [STOP] state and display [STOP] on DVD display panel. At this time, you can press a numerical key to select a file and play the disc starting with the selected file or press [PLAY] key to play the disc starting with the first file of this disc. This file may be either an MP3 file or [MPEG] file. When an MP3 is being played, you can press [DISPLAY] key to view file play time. Note:1. If you are not quite familiar with thisunitand press [PROG] key Or select programming function through the menu when the discs described above are played, error operations will be caused. If your disc contains files of multiple formats, press [STOP] key after the play of the disc is finished and display the picture that you can`t usage [UP]or[DOWN ]key controled the menu. But you may press Previous or Next key to view track numbers in the list on the right side or directly press a numerical key to select a track to play. After a JPEG file disc is read out, you can press PLAY key to start playing. System setting 6. System setting Push [SETUP], the screen will display system setting menu, the moment you can push [UP], [DOWN] to move the high lighting band to the desired item, push [ENTER] to display sub-menu. In the sub-menu push [RIGHT] to enter inferior sub-menu. You can push [UP], [DOWN] to move the high lighting band in all menu pictures. Push [ENTER] your selection will be valid. Push [LEFT] to escape the sub-menu in the right of the screen. Any time push [SETUP] or [EXIT SETUP] you will escape system setting state. Attention: While playing, you can push [PREVIOUS] or [NEXT] to play the previous track or the next one. While playing you can push [STOP] to back to the menu picture. The high lighting band indicates current item The explanation to the current item Following are some examples of frequent setting the user can setting other items following their instructions. Example 1:Set TV screen ratio mode 1. Push [SETUP] to enable the screen display the system setting picture, make sure the high lighting band has been located in GENERAL SETUP push [ENTER], TV screen will display following picture. 14 15 System setting System setting 2. Push [RIGHT] to enter the sub-menu in the sub-menu in the right screen. If you want to set the screen to "WIDE", firstly push [DOWN] twice to move the high lighting band to "WIDE' item, then push [ENTER], 3. Push [MAIN PAGE] to exit system setting. Notes:three screen ratio modes, i, e, 16:9 WIDE, 4:3 PS, 4:3 L are available for your selection to enable different discs to match TV. the relationship between the video of disc and screen ratio mode are as follows: once to move the high lighting band to "STEREO" item, then push [ENTER]. 3, Push [MAIN PAGE] to exit system setting page. Example 3: Coaxial output If the user use coaxial terminal to output audio signal, you need to set the audio output "SPDIF/RAW' or "SPDIF/PCM", you can operate following these procedures: Push [SETUP] to enable TV screen display system setting menu picture, please firstly enter general setting sub-menu, then select the item "AUDIO OUTPUT" in the menu, then push [ENTER], TV screen will display: Video of disc 4:3 normal 4:3PS 4:3LB 16:9 16:9 16:9 Example 2:Set sound mix output mode 1. Push [SETUP] to enable TV screen display system setting menu picture, push [DOWN] to move the high lighting band to the item "SPEAKER SETUP", push [ENTER], TV screen will display 2. Push [RIGHT] to enter the sub-menu in the right screen, If you 2. Push [RIGHT] to enter the sub-menu in the right screen, push [DOWN] to move the high lighting band to the item "SPDIF/RAW" or "SPDIF/PCM", then push [ENTER]. 3. Push [MAIN PAGE] to exit system setting. [. . . ] Technical terms TITLE:For DVD disc it is defined as a long complete segment of image or music or a movie. Each title has a number that makes it easy to search. TRACK: The image or music of a VCD or CD. CHAPTER:It is smaller than title among the units of a DVD, it is defined as a long complete segment of image or music or a movie. [. . . ]