User manual PYLE PLTVD7.5N

[. . . ] MOTORIZED 7" WIDE TFT LCD MONITOR WITH COLOR TV MODEL NO. : PLTV7. 5DIN 1 ANY CHANGES OR MODIFICATIONS IN CONSTRUCTION OF THIS UNIT DEVICE WHICH IS NOT APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. WARNING DO NOT WATCH MONITOR WHILE DRIVING 2 CONTENTS WARNING CAUTION UNIT 1. REMOTE CONTROL BATTERY BASIC OPERATION 1. ADJUSTING LEFT/RIGHT VIEWING POSITION 7. [. . . ] 2) Press SEARCH / button to select TILT POSITION. 3) Press VOLUME button to swing the LCD panel one step backward. Press VOLUME button to swing the LCD panel one step forward. The TILT position is +2, +1, 0, -1, -2. 3. MOVE POSITION CONTROL 1) Press MENU button to show FUNCTION on the screen. 2) Press SEARCH / buttons to select MOVE POSITION. 3) Press VOLUME button to move the unit one step forward(50mm). The menu will show the position at 1, 2, 3. Press VOLUME button to move the unit one step backward(50mm). The menu will show the position at 2, 1, 0. 15 CONTROL 1. NAVIGATION AUDIO ( In case, you use an optional compatible Navigation System) When a navigation system is connected to this unit, you can use the navigation system properly after you adjust the navigation audio control. If you press NAVI button on the remote control, the navigation mode will be displayed on the screen on any mode, when you connect the navigation system to this unit, you should connect it through RGB connector at the backside of this unit NOTE This is limited to only the unit with RGB connector. Press MENU button to select CONTROL menu, and press SEARCH / button to select NAVI AUDIO. Press VOLUME or button to change the navigation audio as follows. OFF -> ON -> AUTO OFF ON : When a navigation system is not connected, the NAVI AUDIO should be set to OFF. : When a navigation system is connected to this unit through RGB connector, the NAVI AUDIO should be set to ON or AUTO. When the NAVI AUDIO is set to ON on the navigation mode, only the navigation audio is heard through the speakers. AUTO : When the NAVI AUDIO is set to AUTO on the navigation mode, the previous mode audio (TV) is heard through the speakers, when the navigation audio comes on, the previous mode audio is muted and the navigation audio is heard through the speakers. 16 2. SCREEN ASPECT CONTROL 1) Press MENU button to show CONTROL on the screen. 2) Press SEARCH / button to select SCREEN. 3) Press VOLUME or button to change SCREEN aspect. Each time you press this button, SCREEN will be changed as follows. [. . . ] If it is grounded, the unit can be damaged. 27 CONNECTING TO AV SOURCES 28 SPECIFICATIONS General Power Supply Power Consumption Operating Temperature Audio Input Sensitivity Audio Output Voltage Video Input Signal Video Output Signal Dimensions Polarity Fuses Weight Net Gross Monitor Section Screen Size LCD Type LCD Drive System Number of Pixels Effective Pixels Back Lighting Color System FM Transmitter Frequency TV Section Receiving Channel VHF LOW (S3-NZ1) VHF HIGH (E12 ­ E5) UHF (E69 ­ E21) DC 14. 4V(11V-15V) 1. 5A -10 degree~ 60 degree 1. 0V/22K Ohm 0. 5V/1K Ohm 1. 0Vpp/75 Ohm 1. 0Vpp/75 Ohm 178(W) x 25(H) x 160(D)mm Negative Ground only 2A(Back Up) 3A(ACC) 1. 5Kg 2. 2Kg 7 Inch Wide Transparent Type TN LCD TFT Active Matrix 336, 960(1, 440 X 234) 99% or more U-shaped cold cathode Fluorescent Tube NTSC ONLY 89. 5 MHz ~ 90. 2 MHz Specifications are subject to be changed without notice. 29 TROUBLE SHOOTING GENERAL Problem Power not turn on. (No sound is produced. ) Nothing buttons pressed. The remote Direct rays of the When direct rays of the sun fall on the sun fall on the light-receptive part of the remote light-receptive part of the remote controller. The batteries of Check the batteries of the remote controller the remote unit. [. . . ]