User manual PYLE PLVHR72 INSTRUCTION MANUAL

[. . . ] 7" Wide LCD Monitor With 4 Mounting Options PLHR71 AU RM -1 0B PLVHR72 INSTRUCTION MANUAL www. pyleaudio. com Table of Contents About the liquid crystal display (LCD) panel Troubleshooting guide Precautions Control & Layout for monitor / wireless remote Accessories Connection diagram Replacing the remote control battery Installing headrest with shroud Installing sun-visor with shroud installing of headrest case Function setting Specifications 2 3 3 4 5 6 6 7-8 9-10 11 12-22 23 1 About the liquid crystal display (LCD) panel 1. Do not press on the LCD panel on the monitor unit as doing so can distort the picture or cause a malfunction, the picture may become unclear, or the LCD panel may be damaged. Notes on cleaning -clean the LCD panel with a slightly damp soft cloth. - do not use solvents such benzine, thinner, commercially available cleaners or antistatic spray. [. . . ] 9) Keep the lithium battery out of the reach of children. Should the battery be swallowed, immediately consult a doctor. 10)If the MONITOR does not operate even when you operate the remote control from a close range, it is time to replace the battery (use CR-2025 lithium battery), refer ring to the label on the back of the basic control. 11)Do not hold the battery with metallic tweezers, otherwise a short-circuit may occur. 6 Steps For Installing Headrest with Shroud Setup work Remove the headrest and set it in an uncluttered work area. Pay the appropriate precautions to ensure that it is not damaged during the installation. CAUTION: make sure the screws are not long enough to go through the headrest!If you have any doubts about this type of installation, please consult your local mobile electronics retailer. Cutting and making holes in the headrest will cause electronic damage which is expensive to repair. Measurements Press the headrest with your fingers to make sure there are no obstructions that would hinder the installation. Use paper template to mark the area to be cut. Cut the headrest Use an adjustable-depth blade, start your cut 1/4 inch inside one corner and cut diagonally across, stopping 1/4 inch in from the other corner. Repeat this procedure for the other two corners. Remove foam & obstructions Carefully peel off the material. Set the adjustable blade to one inch depth and cut around the edges of the hole, staying 1/4 inch inside the edge. Pull up one corner of the foam and use the blade to cut underneath. Remove small section at a time and ensure to be the uniform depth. Use a dremel or other appropriate tools to remove other obstructions. Insert the monitor to measure the fit and make adjustment if necessary 7 Route the cable through the headrest Run the supplied cable through the opening and out to the bottom of the headrest. If possible, conceal the wires with a shaft covering. Connect the power, ground and video leads to test the MONITOR. Before connecting the monitor, pull the connecting cable through the headrest shroud as shown in diagram. Place the headrest housing into the opening and secure with correct fasteners. Install the headrest shroud Pull the connecting cable through the center of the shroud as shown in diagram, and secure the headrest shroud with correct fasteners Insert the monitor Push to insert the monitor to the headrest shroud. Removal Insert the release key between the monitor and headrest shroud gap and pull it out to remove the monitor from headrest shroud. 8 Steps For Installing Sun-visor with Shroud Setup work Remove the visor and set it in an uncluttered work area. Pay appropriate precautions to ensure that it is not damaged during the installation. CAUTION: make sure the screws are not long enough to go through the visor!If you have any doubts about this type of installation, please consult your local mobile electronics retailer. Cutting and making holes in the visor will cause electronic damage which is expensive to repair. Measurements Press push on the headliner with your fingers to make sure there are no obstructions that would hinder the installation. Use paper template to mark the area to be cut. Cut the visor Use an adjustable-depth blade, start your cut 1/4 inch inside one corner and cut diagonally across, stopping 1/4 inch in from the other corner. [. . . ] Press menu button (1) to enter scaling setting. [Scaling: adjusts picture size full screen, letter box & paranormal] Contrast Brightness Hue Saturation Gamma Function Scaling Return 2 9 EXIT 1 3 Remote SEL. Video Signal MU ADJ. DDP RET Others Monitor Picture Parameters OSD Setup OSD Press the button( 2or3) to adjust the symbol to choose "full screen:. Press menu button (1) setup as full screen. The symbol show current selection. [An image with an aspect ratio of 4:3 enlarge to the left & right edges of the screen] Scaling Full Screen Letter Box Paranoma Return 2 1 SEL. MU SET. EXIT RET Remote 3 17 Monitor Video Signal Picture Parameters DDP OSD Setup Others OSD Press the button( 2or3) to adjust the symbol to choose enable. Press menu button (1) setup as clearness picture. [. . . ]